Fitting Instructions Code Handle ® Window; 1. Code Handle Window; Insert Batteries - Assa Abloy Code Handle Window Instrucciones De Montaje

Fitting Instructions Code Handle
ENG
Prepare for installation
Check that all parts are included as described on
page 3:

1. Code Handle Window

2. Mounting screws:
a. 2 x M5 screws (Phillips 2)
b. 2 x M5 one-way screws
3. 2 x Batteries AAA, Alkaline LR03
4. Tool for removal of battery hatch
5. 3 x spindles (different lengths)
Verify that you have the tools necessary for for instal-
lation.
Important about batteries
ASSA ABLOY Code Handle is battery operated and
is delivered with batteries that need fitting prior to
installation/operation. Always use alkaline batteries
type AAA (LR03).
See inside of back cover for pictures supporting
programming and installation instructions
below.
1

Insert batteries

a. Remove the screw at the end of the handle by using
the tool provided. Pull out the battery holder.
b. Fit the two (AAA) batteries into the battery holder
according to the indication.
c. Insert the battery holder into the handle. Tighten
the screw using the tool provided.
2
Enter/change administrator code
All ASSA ABLOY Code Handles are delivered with
the same administrator code from the factory. For
sequrity reasons, always change this to your own
administrator code before using the lock.
If the administrator code is lost, the handle cannot
be re-programmed. It is therefore very important
to write down your administrator code and store it safely.
The administrator code is used to add/erase user
codes and to enable/disable the audio signal as des-
cribed below. When changing the administrator code,
the handle will reset to factory settings (audio signal
enabled and user codes erased).
a. Before you start, write down the new administrator
code on page 2 (6 digits).
b. Hold the lock button pressed to enter program-
ming mode. The LED turns steady green.
c. Enter the existing administrator code (new handle:
123412). The LED turns steady green.
4
Window
®
d. Press button 3 to change the administrator code.
The LED turns steady green.
e. Enter the new administrator code according to step
(a) – 6 digits. The LED turns steady green.
f. Re-enter your new administrator code. The new
code is now set. The LED flashes green along with
a long beep.
g. Store your codes and this manual safely!
Note: The administrator code can also be used as a
user code to unlock the handle.
3 Select/adjust spindle length
a. Attach a spindle to the handle by pressing it into
the square hole. Ensure that the spindle is rotated
correctly so that the clips secure the spindle by its
grooves.
b. Fit the handle temporarily to the window/patio
door without attaching the screws. If there is a gap
between the handle plate and the window frame,
try a shorter spindle.
to
1 7
c. When replacing an existing handle, select a spindle
that is equal or slightly longer than the old spindle,
or insert the longest spindle and cut it to the
appropriate length.
4
Fit the handle
Before fitting the handle, ensure that the Code Handle
Window functions with the newly registered code.
Press the lock button to lock and use the new admi-
nistrator/user code to unlock.
a. Pull off, and turn the cover plate on the handle
plate to uncover the holes for the screws.
Do not use one-way screws in the following step.
b. Fit the handle to the window in the closed position.
- Insert the M5 Phillips screw in the hole above the
handle and fasten.
- Turn the handle (hence opening the window/win-
dow door) to reveal the other hole and fasten the
second M5 Phillips screw.
c. Refit the cover plate by turning it to the right posi-
tion and pressing it onto the handle plate. Now
test each function (unlock, open window, close
window, lock).
d. Optional: Additional security can be achieved by
replacing the M5 screws with one-way screws.
Note: All inputs on the keypad are also confirmed with a
beep if audio signals are enabled.