Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION INSTRUCTIONS - ENGLISH
2
BE SURE MOUNTING AREA IS CLEAN AND DRY.
FOR SIDE SPRAY
MODEL ONLY GO
TO STEP 3.
HINTS: When using flexible supplies, we recommend supply lines be
installed onto threaded fittings before placing faucet through sink holes
(see step 6). For installations on tile countertops, remove rubber gasket from
underneath support plate (19) and apply a bead of putty in its place. Roll the
bead of putty into a diameter no larger than a pencil. When applied in the
groove, the putty bead should protrude a minimum of 1/16".
4a
GROOVE
➤
4a. Install faucet through deck holes (threaded
shank (22) to back). Center faucet on sink
with support plate (19) oriented in sink
holes. Position spout to the side to keep
faucet from tilting forward. Go to step 4b
for installation of mounting bracket (24).
5
25
5. Be sure faucet is positioned evenly on
sink. Make final tightening of mounting
nut (25) with a basin wrench, channel
locks, or 5/8" deep socket wrench.
Go to step 6.
NOTE: Models with 16" long supply
tubes connect directly to stop valves.
FOR WITHOUT SPRAY
MODEL GO TO
STEP 4a.
22
Threaded
shank to
back
24
25
6
6. If using flexible supply lines with compression
fittings, thread supply line nuts on finger tight,
then holding one threaded fitting with a wrench,
tighten nut with another wrench, rotating one
half turn. Do not overtighten. Make connections
to existing hot and cold stop valves. The hot
supply tube is always to the left when threaded
shank (22) is positioned to rear. Go to step 7.
3
27
3. Locate foam gasket on hose guide (27) by sliding gasket onto
shank and tucking outer edge of gasket under the hose guide (27).
Do not drive the center area of the gasket up into the hose guide.
Install hose guide (27) through furthest left or right hole in sink.
From under sink, thread locknut (28) (flat side up) on shank of
hose guide and tighten by hand. Feed spray hose (29) down
through the hose guide (27) (do not connect spray hose to faucet
until step 7 below). Go to 4a.
4b
For deck holes up to
1-1/8" deep, install
mounting bracket (24)
OPEN SIDE UP.
GROOVE
➤
IMPORTANT: DECK THICKNESS
4b.
As shown above, your deck thickness determines whether the
mounting bracket (24) is installed open side up or down. For side
spray models, a groove on the threaded shank (22) indicates the
minimum amount of thread length which must be exposed for
proper attachment of nuts (25) and (30). For models without side
spray, a minimum of 1/2" of threaded shank (22) must be
exposed for proper attachment of nut (25).
Install mounting nut (25) and tighten by hand. Go to step 5.
CAUTION:
Severe bends of the
supply lines may cause
crimping and restricted
water flow could result.
28
27
Back View of Faucet Installation
For deck holes over
1-1/8" deep, install mount-
ing bracket (24)
OPEN SIDE DOWN.
24
24
22
25
25
7
29
TO CONNECT SPRAY HOSE
(SIDE SPRAY MODELS ONLY):
7. Connect spray hose swivel nut (30) to the
threaded shank. Tighten swivel nut by hand
plus 1/4 turn with pliers or channel locks
being careful not to twist the hose (29).
DO NOT OVERTIGHTEN.
Faucet flushing is required. See flushing
instructions on next page.
26
29
22
30
2
continued
Publicidad
