Descargar Imprimir esta página

Juliana Veranda Instrucciones De Montaje página 4

Ocultar thumbs Ver también para Veranda:

Publicidad

May we congratulate you on your new greenhouse
GB
Dear Customer!
DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
in the instructions. Assemble one pack at a time.
corresponding to the order in the assembly
All nuts, bolts and fittings are contained in bag No.
instruction. Erect one pack at a time. All nuts
0 (specified on page 12). Each pack is specified in
and bolts and fittings are found in bag No. 0
separate lists of components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside
Seen from the outside
Seen from inside
Seen from outside.
SOME SAFETY PRECAUTIONS
Assembly must only be carried out in dry and
calm weather.
Precautions.
Always wear work gloves when installing the
Assembly must only be carried out in dry
glazing. Greenhouse glass has sharp edges,
and calm weather.
especially if it breaks.
Always use working gloves while glazing.
Assistants and especially children must be
Greenhouse glass has sharp edges,
warned that broken glass is dangerous. Pick
especially if the glass breaks.
up all broken glass at once and remove it with
Assistants and especially children must be
care.
We recommend that you wear protective
warned that broken glass is an element of
glasses while fixing the spring wire clips.
danger. Pick up broken glass at once and
Any ladders that are used must be placed on a
remove it with care.
level surface.
We recommend to use protective glasses
It is essential to have an assistant available.
while fixing the spring wire clips.
Place the ladder on a level support.
PAGE 12: TOOLS
It is essential to have an assistant.
Assembling the greenhouse requires the tools
shown on page 12.
References
PAGE 13: FOUNDATIONS
The column marked
indicates the
No base is included with this product. However, an
page(s) on which the component is used.
original base is available separately. This base is easy
to construct and will guarantee you a stable base for
Page 13:
your greenhouse.
Foundation
If you construct your own base, the specified
The base is not included in this delivery.
measurements must be external measurements.
However, an original base can be bought
If you purchase an original base, you will also require
about 75 litres of concrete and six to eight plastic/
separately. It ensures you a stable and easy to
concrete pipes of about 800mm. These pipes, which
build base.
must be buried at a sufficient depth to ensure that
If you make your own base the measurements
they do not freeze, secure the corner and middle
indicated must be external measurements.
anchors.
If you buy an original base you furthermore
The base must be completely level and square;
need about 75 litres of concrete and 6/8
the latter can be ensured by checking that the two
plastic-/concrete pipes of about 800 mm which
diagonal measurements are equal.
are placed in a non-freezing depth for the
ATTACHMENT TO THE BASE
fastening of the corner and middle anchors.
If you construct your own base, you must drill holes
The base must be 100% level and square; the
(7mm) in the ground frame between all the vertical
latter is ensured by checking that the two
profiles. The greenhouse must then be secured to
diagonal measurements are equal.
the base using screws (A).
If you use an original base, the greenhouse must be
Tools
secured to each vertical bar as shown on drawings
The mounting of the greenhouse requires the
B/C.
tools shown on page 12.
PAGE 14-27: ORDER OF ASSEMBLY
Place the components as shown on the illustration
Page 14-27:
and assemble in the order shown in the pictures. Do
Place the components as shown on the
not tighten the nuts fully until the entire sub-frame
illustration and assemble in the order shown
has been assembled.
in the pictures. Do not tighten the nuts
completely until the front gable construction
PAGE 22-25: DOORS AND WINDOWS
has been assembled.
For easier assembly, we recommend that you oil the
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be fitted at the same
time as the profiles.
PAGES 28-29: FITTING OF GLASS/
Page 13:
POLYCARBONATE
(Fastening to the base).
Important before assembly!
When constructing your own base you have
Make sure that the gables and sides are level
to drill holes (7 mm) in the ground frame
and square and that door(s) and window(s) are
between all the vertical frames, the greenhouse
functioning perfectly.
is then fastened to the base with screws (A).
Using an original base the greenhouse is
The best order of assembly for the glass or
fastened to each vertical bar as shown on
polycarbonate is as follows:
Windows - Roof - Doors - Gables - Sides
drawing B/C.
PAGE 28-29: GLASS INSTALLATION
Page 24-27:
Degrease the sheets and frames with spirit.
For an easier assembly we recommend that you
Start glazing, one pane at a time. Apply a 3mm
oil the screws for the doors.
silicone bead around the vertical frames as indicated
(the dotted lines on the illustration). (A 3mm bead of
Fitting of glass/polycarbonate
silicone is sufficient to ensure maximum adhesion).
Important before glazing!
If you use more silicone than recommended, extra
tubes can be purchased.
Make sure that gables and sides are level and
If you accidentally break a pane, carefully pull the
square, and that door(s) and window(s) are
broken glass outwards and loosen the silicone using
functioning perfectly.
a sharp craft knife.
Clean the profile completely before inserting a new
Best order of assembly:
pane of glass.
1) Windows – 2) Roof – 3) Doors – 4) Gables
– 5) Sides
PAGE 28-29: POLYCARBONATE INSTALLATION
The illustrations at the bottom of pages 28-29 show
where to fit the polycarbonate sheets and strips. The
Page 30-33:
type designation states the length in millimetres. If
Glazing (illustration 1 to 8)
adjustment is necessary, use a fine-tooth saw.
Degrease the sheets and frames with spirit.
NB! To avoid the growth of algae, prevent the
Start glazing from below, one glass at a time.
polycarbonate sheets from coming into contact with
Apply a 3 mm silicone line on the vertical
the ground by resting them on a sheet of cardboard.
frames where indicated (dotted lines on
the illustration). (A 3 mm line of silicone is
M-strips are fitted as shown on pages 28-29. Place
the upper part of the strip under the aluminium
sufficient to obtain maximum attachment). If
profile along the full length of the sheet and then
you do use more than recommended, you can
click the strip into position from above.
buy extra tubes.
U-strips are fitted as shown on pages 28-29.
Spring wire clips and glassholders are to be
Fit the strip to the sheet and adjust the length.
fitted as shown.
X = Spring wire clips, > = Glassholders
If desired, the sheets may be sealed against insects.
Seal the top using aluminium tape or silicone. The
In case of broken glass carefully pull it
bottom should only be sealed with air-strip tape to
allow condensation to escape (available from your
outwards and loosen the silicone by means of a
local dealer).
sharp craft knife.
Clean the profile completely before inserting a
Your greenhouse is now fully assembled. However,
new pane of glass.
please note the following:
Page 34-37:
MAINTENANCE
Mounting of polycarbonate
Grease the doors (hinges and locks).
The illustrations at the bottom of page 34/36
Keep the gutters free from leaves, etc.
Adjust the windows as necessary.
show where to mount the polycarbonate plates
Replace any broken glass.
and lists. The type indication states the length
Clean the greenhouse with disinfectant before
in mm. A possible adjustment is made by
and after the growing season.
means of a fine-tooth saw.
NB! To avoid the formation of algae the
WINTER PROTECTION
polycarbonate sheets must not come into
If you anticipate snow during the winter, we
contact with the ground. Rest them on a piece
recommend the following winter precautions:
of cardboard.
Support the apex of the roof in the middle.
Remove any deep snow from the roof.
Take precautions to prevent snow falling from
A-lists are mounted as shown on page 35/37.
a tree or roof, for example.
Put the sheet into the bottom list, bend the
Remove the cylinders for the automatic
sheet slightly outwards and put it in the top list.
window openers, if fitted (optional extras).
Secure the door(s) and window(s) to prevent
M-lists are mounted as shown on page 35/37.
wind damage to the greenhouse.
Place the upper part of the list under the alu.
profile in the whole length of the sheet and
WATER AND CONDENSATION
Please note that your greenhouse is not like a
hereafter click on the list from above.
conservatory, for example, and that you should
therefore be aware that the greenhouse may leak
B
during or after precipitation and that condensation
Sealing of the polycarbonate sheets
will occur on the inside of the greenhouse. Good
The sheets may be sealed against insects.
ventilation will help prevent condensation.
Close the top end off with alu-tape or silicone.
The bottom only with airstrip tape to let
INSURANCE
condensation out (available at your local
Please note that not all insurance companies cover
dealer).
greenhouses automatically. Please contact your
insurance company to ensure that your greenhouse
is covered.
Now your greenhouse is completely assembled.
However, please notice the following:
GUARANTEE
Juliana greenhouses are covered by a 12-year
Maintenance
guarantee, which covers the replacement or repair
Grease doors (hinges and lock).
of faulty parts. The guarantee does not cover
Clean the gutter for leaves, etc.
polycarbonate, glass, transport, assembly, freight,
Adjustment of windows.
etc.
Replacement of broken glass.
Juliana greenhouses are covered by a two-year
warranty on painted parts, where fitted. Note that
Clean the house with disinfectant before
marks on the paint may occur due to suspension of
and after the growing season.
the profiles.
The guarantee will be void if the greenhouse is not
Winter Protection
assembled in accordance with these instructions.
In areas with occurrence of snow we
recommend the following winter protection:
COMPLAINTS
Support the roof ridge at the centre of the
All our greenhouses are built to the highest quality
house.
standards. However, should you experience any
problems, please contact your dealer at once. When
Remove greater snow loads from the roof.
describing the defect, please state the greenhouse
Take precautions against snow falling
model, the component number and the quality
down from for instance a tree or a roof.
control number.
Dismount the cylinders for the automatic
window openers, if any (optional extras).
Congratulations on your new greenhouse, which we
Secure door(s) and window(s) preventing
hope will bring you a lot of pleasure for many years
wind damage to the house.
to come.
Yours sincerely,
Insurance
Please note that not all insurance companies
Juliana Drivhuse A/S
cover glasshouses automatically. Please
contact your insurance company to ensure an
insurance coverage.
Guarantee
Juliana grants a guarantee of 12 years which
covers replacement of faulty parts. The
guarantee does not cover polycarbonate, glass,
transport, assembly, freight etc.
Juliana grants a guarantee of 2 years on painted
parts, if any. Note that marks in the painting
may occur due to suspension of the profiles.
The guarantee is invalid if the greenhouse is
not assembled according to these instructions.
Complaints
All our greenhouses are built to high standards
of quality. However, should a complaint
occur please contact your dealer at once.
Remember to specify the defect by indicating
the greenhouse model and number of the
component and the quality control number.
USA

Publicidad

loading