Milwaukee 2310-21 Manual Del Operador página 2

GENERAL POWER TOOL SAFETY WARNINGS
READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fi re
and/or serious injury.
Save all warnings and instructions for future reference
WORK AREA SAFETY
• Keep work area clean and well lit. Clut-
tered or dark areas invite accidents.
• Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
• Do not operate power tool in an area
where it could contact electrical wir-
ing or an electrically charged object.
Contact with a "live" wire or object will
make exposed metal parts of the tool
"live" and shock the operator.
• Do not operate power tool near moving
machinery. The cable can be tangled in
moving parts, pulling in the power tool and
your hands and arms.
• Do not use near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifi ers) that
produce heat.
• Keep children and bystanders away
while operating a power tool. Distrac-
tions can cause you to lose control.
ELECTRICAL SAFETY
• Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
Dry hands before turning tool on or off and
before removing or installing the battery
pack.
PERSONAL SAFETY
• Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power tool
while you are tired or under the infl u-
ence of drugs, alcohol or medication.
A moment of inattention while operating
power tools may result in serious personal
injury.
WARNING
• Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protec-
tion used for appropriate conditions will
reduce personal injuries.
• Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unex-
pected situations.
POWER TOOL USE AND CARE
• This Visual Inspection Camera is not
intended for medical use or personal
inspection.
• Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
• Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tool op-
eration. Do not use if power tool smokes
or gives off fumes. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
• Use the power tool, accessories and
tool bits etc., in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation. Only
use accessories specifi cally recommended
for this tool. Others may be hazardous.
• Clean only with dry cloth. Certain clean-
ing agents and solvents are harmful to
plastics and other insulated parts. Some of
these include: gasoline, turpentine, lacquer
thinner, paint thinner, chlorinated clean-
2
ing solvents, ammonia and household
detergents containing ammonia. Clean
dust and debris from vents. Keep the ap-
paratus handle clean, dry and free of oil or
grease.
• Always remove the battery pack before
cleaning.
BATTERY TOOL USE AND CARE
• This tool is designed to be powered by
a 12 volt MILWAUKEE battery pack (Cat.
No. 48-11-2401). Do not attempt to use
with any other voltage or power supply.
• Recharge only with the charger speci-
fi ed by the manufacturer. A charger that
is suitable for one type of battery pack may
create a risk of fi re when used with another
battery pack.
• Use power tools only with specifi cally
designated battery packs. Use of any
other battery packs may create a risk of
injury and fi re.
• When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws, or other
small metal objects that can make a con-
nection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fi re.
• Under abusive conditions, liquid may
be ejected from the battery, avoid
contact. If contact accidentally occurs,
fl ush with water. If liquid contacts eyes,
additionally seek medical help. Liquid
ejected from the battery may cause irrita-
tion or burns.
SERVICE
• Contact a MILWAUKEE service facility
for ALL repairs. Have your power tool
serviced by a qualifi ed repair person
using only identical replacement parts.
This will ensure that the safety of the power
tool is maintained.
• Never disassemble the power tool or try
to do any rewiring on the power tool's
electrical system.
SPECIFIC SAFETY RULES
• Maintain labels and nameplates. These
carry important information. If unreadable
or missing, contact a MILWAUKEE service
facility for a free replacement.
• WARNING: Changes or modifi cations to
this unit not expressly approved by the party
responsible for compliance could void the
user's authority to operate the equipment.
Use of shielded cable is required to comply
with Class B limits in Subpart B of Part 15
of the FCC rules.
Federal
Communications
Commission
Operation is subject to the following two
conditions:
1. This device may not cause harmful inter-
ference.
2. This device must accept any interference
received including interference that may
cause undesired operation.
This equipment has been tested and found
to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC
Rules. These limits are designed to pro-
vide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interfer-
ence to radio communications.
However, there is no guarantee that inter-
ference will not occur in a particular instal-
lation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encour-
aged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving an-
tenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Use of shielded cable is required to comply
with Class B limits in Subpart B of Part 15
of the FCC rules.
Specifi cations
Cat. No. Volts
2310-21 12 DC
3