Filling The Oil Reservoir - Craftsman CMECS600 Manual De Instructiones

English
Replacement chain and bar are available from your
nearest authorized service center.
• This chain saw requires replacement 16" (406 mm) chain
CMZCSC16. Replacement 16" bar CMZCSB16.
Saw Chain and Guide Bar Oiling (Fig. A)
Auto Oiling System
This chain saw is equipped with an auto oiling system that
keeps the saw chain and guide bar constantly lubricated.
The oil level indicator 15 shows the level of the oil in the
chain saw. If the oil level is less than a quarter full, unplug
the chainsaw and refill with the proper oil.
nOTE: Use a high quality bar and chain oil for proper saw
chain and bar lubrication. As a temporary substitute, a non-
detergent SAE30 weight motor oil can be used. The use of
a vegetable based bar and chain oil is recommended when
pruning trees. Mineral oil is not recommended because it
may harm trees. Never use waste oil or very thick oil. These
may damage your chain saw.

Filling the Oil Reservoir

1. Remove the oil cap 14 and fill the reservoir with the
recommended chain oil until the oil level has reached
the top of the oil level indicator
2. Refit the oil cap.
3. Periodically switch the chain saw off and check the oil
level indicator to ensure the bar and chain are being
properly oiled.
Attaching Extension Cord (Fig. H)
An extension cord retainer 13
switch handle. It prevents the extension cord from
coming unplugged.
• Double the extension cord and insert it into the slot
in the end of the handle area as shown in Figure H.
Hook the loop formed by doubling the cord over the
cord retainer. Gently tug on the cord to ensure that
it is firmly retained in the handle. Plug the receptacle
end of the extension cord into the power cord
the chainsaw.
Fig. H
13
Transporting Chain Saw (Fig. A, I)
• Always turn unit off and disconnect it from power
source and cover the guide bar
scabbard 9 when transporting the saw.
8
15 .
is built into the
21
12 of
21
12
4 with the guide bar
Fig. I
4
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Proper Hand Position (Fig. A)

WARNING: To reduce the risk of serious personal injury,
Always use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
always hold securely in anticipation of a sudden reaction.
Proper hand position requires the left hand on the front
handle 11 , with the right hand on the rear handle
Operating the Chain Saw (Fig. A)

WARNING: Read and understand all instructions.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious personal injury.
• Guard Against Kickback which can result in severe
injury or death. See general Power Tool safety
Warnings, Causes and Operator Prevention
of Kickback and Kickback safety Features ,
to avoid the risk of kickback.
• Do not overreach. Do not cut above chest height.
Make sure your footing is firm. Keep feet apart.
Divide your weight evenly on both feet.
• Use a firm grip with your left hand on the front
handle 11 and your right hand on the rear
handle 10 so that your body is to the left of the
guide bar.
• Do not hold chain saw by front hand guard/
chain brake 3 . Keep elbow of left arm locked so
that left arm is straight to withstand a kickback.

WARNING: Never use a cross-handed grip (left
hand on the rear handle and right hand on the
front handle).

WARNING: Never allow any part of your body to
be in line with the guide bar
chain saw.
• Never operate while in a tree, in any awkward
position or on a ladder or other unstable surface.
You may lose control of saw causing severe injury.
• Keep the chain saw running at full speed the entire
time you are cutting.
• Allow the saw chain to cut for you. Exert only light
pressure. Do not put pressure on chain saw at
end of cut.
9
10 .
4 when operating the