Saw Chain And Guide Bar - Craftsman CMECS600 Manual De Instructiones

Saw Chain Sharpening (Fig. S, T, U)

CAUTION: Sharp chain. Always wear protective
gloves when handling the chain. The chain is sharp
and can cut you when it is not running.

WARNING: Sharp moving chain. To prevent
accidental operation, ensure the tool is unplugged
before performing the following operations. Failure to
do this could result in serious personal injury.
nOTE: The cutters will dull immediately if they touch the
ground or a nail while cutting.
To get the best possible performance from your chain saw
it is important to keep the teeth of the saw chain sharp.
Follow these helpful tips for proper saw chain sharpening:
1. For best results use a 4.5 mm file and a file holder or
filing guide to sharpen your saw chain. This will ensure
you always get the correct sharpening angles.
2. Place the file holder flat on the top plate and depth
gauge of the cutter.
3. Figure s- Keep the correct top plate
of 30° on your file guide parallel with your chain (file at
60° from chain viewed from the side).
4. Sharpen cutters on one side of the chain first. File from
the inside of each cutter to the outside. Then turn your
saw around and repeat the processes (2, 3, 4) for cutters
on the other side of the chain.
nOTE: Use a flat file to file the tops of the rakers (portion
of chain link in front of the cutter) so they are about
.025" (.635 mm) below the tips of the cutters as shown
in Figure T.
5. Figure U- Keep all cutter lengths equal.
6. If damage is present on the chrome surface of the
top plates or side plates, file back until such damage
is removed.

CAUTION: After filing, the cutter will be sharp, use
extra caution during this process.
nOTE: Each time the chain is sharpened, it loses some of
the low kickback qualities and extra caution should be used.
It is recommended that a saw chain be sharpened no more
than four times.
Fig. S
23
Fig. T
Fig. U
Cleaning


23 filing angle line
Regular maintenance ensures a long effective life for your
chain saw.

Saw Chain and Guide Bar

After every few hours of use, remove the guide bar and
clean thoroughly.
Register Online
Thank you for your purchase. Register your product now for:
•
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
•
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.craftsman.com/registration
Three Year Limited Warranty
CRAFTSMAN will repair or replace, without charge, any
60°
defects due to faulty materials or workmanship for three
years from the date of purchase. This warranty does not
cover part failure due to normal wear or tool abuse. For
further detail of warranty coverage and warranty repair
information, visit www.craftsman.com or call
1-888-331-4569. This warranty does not apply to
.025"
accessories or damage caused where repairs have been
(0.635 mm)
made or attempted by others. THIS LIMITED WARRANTY
IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
English
11