THERMEx DECOR 902 Montaje Y Modo De Empleo página 3

INSTRUCTION ON MOUNTING AND USE
GB
Consult the designs in the front pages referenced in the text
by alphabet letters. Closely follow the instructions set
out in this manual. All responsibility, for any eventual
inconveniences, damages or fires caused by not complying
with the instructions in this manual, is declined.
Installation - Fig. 1
The cooker hood must be placed at a minimum distance of
50 cm from the cooking plane for electric cookers and 70 cm
for gas or mixed cookers.
If the instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
1 . Position the perforation template on the wall and make
a VERTICAL LINE with a pencil to extend the line printed
on the template. It will help during the montage.
2 . Make 2 holes as shown on the template.
3 . Remove the template and insert two hooks (supplied
with screws and expansion dowels) in the holes just
made.
4 . Remove the anti-fat filters, pulling the handles backward
and in this way unhooking the hooking pins.
5 . Position the hood at the desired point (adjust the position
of the hood tightening or loosening the screws on the
hooks of the hood).
6 . Mark 2 holes to make on the wall (upper part of the hood).
7 . Make 2 Ø 8 mm holes and insert two expansion dowels
into these holes.
8 . Fix the hood definitively with 2 4x45 screws.
9 . Make 2 Ø 8 mm holes in the wall in correspondence with
the ceiling (use the flue supports as a template), and insert
2 expansion dowels into these holes.
10. Position the flue support, making sure that its centre mark
corresponds with the line previously marked (see point
1).
11 . Fix the support with the 2 5x45 screws supplied.
12. (Only aspiration version) Take the evacuation flange
and fix it onto the exit of the hood with two screws. (Only
filtering version) Ix with 2 screws (see fig. 2)
13. (Only aspiration version) Position the Ø 125 mm
flexible tube onto the evacuation flange on the upper part
of the hood with two screws…. (see fig.2) and install an
exit for external evacuation (through the ceiling, the wall
or an evacuation conduit).
(Only filtering version)...the deflector on the upper part
of the hood (see fig. 2).
14. Carry out the electrical connection. In terms of the law,
the hood must be connected to the power network by
230V.
15 . Put the flue in the desired position.
16 . Fix the upper part of the flue to the flue support with the
2 screws.
17 . Let the lower part slide in its sheath onto the upper part
of the hood so that it acts as a cover for the motor group.
18. Mount the 2 plastic grills respectively onto the right and
left parts of the flue.
Attention!
Never connect the aspiration version hood to a pre-existing
system or a chimney flue.
MODEL WITH RECIRCULATION
The air is filtered through 2 active carbon filters (additional
accessories to order with order number 535.20.4900.9
(1 piece) and then returned into the room again.
Changing the carbon filter:
- Remove the anti-fat filter (see point 4 above).
- Insert the carbon filters directly onto the motor, on the right
and left sides respectively.
Then rotate the filters until they hook onto the bayonet
clamp.
- Remount the anti-fat filter.
COMMAND PANEL (FIG. 3)
a) Light On/Off
b) Ventilator On/Off
c)-d)-e) Speed 1-2-3.
ILLUMINATION
Decor 902: E 14 2 x olive-shaped bulb.
Decor 903: 20 W halogen spotlights.
Instructions for the halogen lamp (only model Décor
903) (FIG. 4).
Changing the lamp: open the overhead lamp/ lamp
protection with a small screwdriver or similar tool.
Use max 20 W (G4) lamps exclusively. Take care not to
touch the lamp with your fingers. Close the protection (trigger
clamp).
This appliance is marked according to the European
directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
The symbol on the product, or on the documents
accompanying the product, indicates that this appliance
may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the
recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local
environmental regulations for waste disposal.
For more detailed information about treatment, recovery and
recycling of this product, please contact your local city office,
your household waste disposal service or the shop where
you purchased the product.