REVELL ACROBAT XP Manual Del Usuario página 8

• Always ensure that the charging
process takes place on a fireproof
surface in a fire-resistant environment.
• Do not leave the battery unsupervised
during the charging process.
• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they must
be discharged or their capacity must
be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
1 HELICOPTER
1A Rotor blades 2A Display
1B Flybar 2B Trim for rotation
1C Tail rotor 2C Control for thrust and
rotation
1D Battery compartment
2D Turbo button
2E Power LED
2F Antenna
2G ON/OFF switch
3 INSERTING BATTERIES (REMOTE CONTROL)
3A To open the battery 3B Insert 6 x 1.5 V AA batteries
compartment, slide the and pay attention to the
cover down.
polarity specifications, as
indicated in the battery
compartment.
4 CHARGING THE HELICOPTER
Attention: The battery and motor must cool down for 15 to 30 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
•Unplug the battery from the model and switch off the remote control. Connect the
USB cable to the charger and insert it in an available USB port 4A.
14
Technical changes and differences in
color reserved!
Required batteries for the helicopter:
Power supply:
Rated output: DC 3,7 V / 0,5 Wh
Batteries: 3,7 V rechargeable
LiPo battery (included)
Capacity: 130 mAh
Battery requirement for the
remote control:
Power supply:
DC 9 V
Batteries: 6 x 1.5 V "AA"
(not included)
Charger:
Input: DC 5 V ;
Output: DC 4,2 V 50 mA
2 REMOTE CONTROL
2H Trim for forwards and
backwards
2I Control for forwards/
backwards
and sideways
2J Trim for sideways
2K Battery compartment
cover
3C Slide the cover up
and close.
• Now insert the battery into the charger from above. Pay attention to the polarity.
The groove of the battery fits into the recess of the holder 4B. The battery must
be gently inserted into the charging socket – DO NOT USE FORCE. If the battery is not
correctly inserted into the charging socket, the battery may become damaged and,
under certain circumstances, cause injury.
• The LED on the charger will light up red when charging begins.
• The charging process lasts approx. 45 minutes and must be continuously monitored.
The red LED on the charger goes out as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
After a charge time of approx. 45 minutes the Helicopter can fly for
approx. 5-7 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 START PREPARATION
The helicopter must be switched on first in order to connect it to the remote control.
For this purpose, insert the battery in the battery holder from behind. Do not use force
and ensure the correct polarity 5A. The groove of the battery fits into the recess of the
holder.After the battery has been inserted into the model, a small red LED inside the
helicopter blinks for a duration of about seven seconds. Switch on the remote control
during these seven seconds. The helicopter may not be moved during this time. The
thrust controller must point down before the remote control is switched on 5B. The
helicopter activates after about five seconds.
6 TRIM ADJUSTMENT OF THE CONTROL
The correct trimming is a basic requirement for achieving fault-free flying from the
helicopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the helicopter approximately 0.5 to 1 metre in altitude.
6A If the helicopter automatically moves slowly or quickly to the left or right ...
gradually press the trim for sideways flight 2J in the opposite direction.
6B If the helicopter moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation 2B incrementally in the opposite direction.
6C If the helicopter automatically moves slowly or quickly forwards or
backwards ...
gradually press the forwards/backwards trim 2H in the opposite direction.
7 FLIGHT CONTROL
Note: Only minimal corrections of the controls are necessary for a smoothing flying
behaviour of the helicopter! The direction information applies if the helicopter is viewed
from behind. If the helicopter is flying towards the pilot, it must be moved in the
opposite direction.
7A Take off or increase altitude by carefully moving the control for thrust and
rotation 2C forward.
7B Land or decrease altitude by moving the control for thrust and
rotation 2C backward.
15