Snapper NXT 7800580 Guía De Instalación Rápida página 2

Overview
Start Button
Starter Insert
Battery Charge
Port
Cutting Height
Adjust Lever
Mulching
Cover
Items that you will need
Utility Knife
Unleaded Fuel (minimum 87 octane)
Items Included
Battery FreshStart
Charger Preserver Cartridge
Mulching Plug Side Discharge SAE30W Starter
(Installed) Grass Bag Deflector Oil Insert
1
Unpack the mower
• Cut all four corners of the box from top to bottom.
• Remove all packing materials from the mower.
• Locate and identify the items included with the mower.
2
Raise the handle assembly
• Loosen, but do not remove, the knobs (A, Figure 1)
on both sides of the upper handle.
• Unfold the upper handle so that it is aligned with the
lower handle, and tighten the upper knobs.
• Remove the knobs, washers and bolts securing the
Drive
lower handle to the mounting brackets (B).
Control (2)
• Raise the lower handle, aligning it with one of the
Blade three sets of holes in the handle bracket. (Most users
will prefer the middle position.) Replace the removed
Control (2)
hardware, tightening securely.
Oil Fill and
Dipstick
3
Charge the battery
Fuel Fill Cap
• Plug the battery charger connector (A, Figure
2) into the charge port on the underside of the
control console.
Fuel Gauge
• Plug the charger into a standard 120-volt outlet
(B). Charge for a period of 12-24 hours.
3-in-1: Convert from mulching to bagging to side-discharge:
1
For mulching:
• Leave the mulching cover and the
installed mulching plug in place (Figure 4).
2
To convert to bagging:
® Fuel
• Lift the rear door and remove the
installed mulching plug (Figure 5).
Operator's
© Briggs & Stratton Corporation
Manual
We reserve the right to improve our products and make changes in specifications, designs, and standard equipment without notice and without incurring obligation.
A
A
B
B
Figure 1
B
A
Figure 2
• Holding the rear door open, attach the
grass bag to the rear of the mower
(Figure 6).
Figure 4
• Make sure the hooks on both sides of
the bag frame hook onto the rear
door rod (Figure 7).
• Release the rear door (it will rest on top
of the grass bag).
Figure 5
7800580
7800696
4
Add oil and fuel
• Move the mower outside to a flat, level surface.
• Remove the oil fill cap (A, Figure 3). Add the entire contents of the
supplied oil container to the engine. Replace the oil fill cap.
IMPORTANT Mower is shipped without oil in engine.
Failure to add oil before starting engine will result in
engine damage.
• Remove the fuel fill cap (B). Following the three-step instructions
on the FreshStart ® card, snap the fuel preserver cartridge into the
bottom of the fuel fill cap.
• Add clean, fresh, UNLEADED fuel with a minimum of 87 octane,
leaving one inch of space from the top of the tank for fuel expansion.
NOTE: Fuel blends containing more than 10% ethanol are not
recommended.
IMPORTANT Fuel tank holds less than 1/2 gallon.
IMPORTANT DO NOT mix oil with fuel.
IMPORTANT DO NOT use E85 fuel.
• Replace the fuel fill cap, and wipe up any spills.
5
Final preparation
• Set the mower to mulch, bag, or discharge.
(See 3-in-1 instructions below.)
6
Read the manuals
• Carefully read all the manuals supplied with the mower.
They contain important safety, operating, and
maintenance information.
3
To convert to side discharge:
• Make sure the mulching plug is installed
in the rear of the mower, and the grass
bag is removed.
• Lift the mulching cover, and install
Figure 6
the side discharge deflector onto the
mower deck (Figure 8).
• Make sure the deck tabs stick up through
the locking slots (Figure 9).
• Release the mulching cover (it will rest
on top of the discharge deflector).
Figure 7
B
A
Figure 3
DANGER
Fuel stabilizer is a hazardous chemical.
IF SWALLOWED, call a physician immediately.
Fuel stabilizer contains:
2,6-di-tert-butylphenol (128-39-2) and
aliphatic petroleum distillate (64742-47-8).
Running engines give off carbon monoxide, an
odorless, colorless, poison gas. Breathing carbon
monoxide can cause nausea, fainting, or death.
Operate this product ONLY outdoors.
Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes or other openings.
DO NOT operate this product inside any building or
enclosure, even if windows and doors are open.
Failure to read and follow instructions in the
operator's manual could result in death and/or
bodily injury.
Figure 8
Figure 9
Form No. 7103489 (Rev. C)