Husky 33094 Instrucciones De Ensamblaje, Instalación Operaciones Y Mantenimiento página 2

NO DESCRIPTION
1 PS BRACKET ASSEMBLY
2 DS BRACKET ASSY
3 RUBBER BRACKET INSULATOR
4 BASE RAIL INSULATOR
5 REAR SPACER
6 FRONT SPACER
7 NYLON TUBE, WEAR RESISTANCE, TALL
1. The following instructions should be used to mount the fifth wheel. Care and attention to detail will ensure a
quick quality installation. Check parts against parts list to become familiar with parts in kit. (See Fig. 1)
2. Lower or removal of spare tire will give more room. Remove wheel well liner to allow access to truck frame.
If the truck is raised, be sure that the truck is properly blocked and restrained to prevent the truck
from falling. Failure to do so may result in the truck suddenly falling, causing death or serious
3. Do NOT install mounting rails over plastic bed liners. Plastic bed liners must be cut out of the way. Base rails
may be installed on spray in liner. Note: Consult installer for recommended curing time.
4. Use only the supplied bolts, nuts and washers to install this kit. All bolts and nuts are Grade 5 unless specified
otherwise.
5. Specific instructions for most commonly used vehicles are included. Each frame bracket must be bolted to the
vehicle frame with two bolts.
These instructions are guidelines only. Actual installation is the responsibility of the installer and
the owner. Always measure truck and trailer before installing hitch to be sure that there is
6. Measurements are given from Rear Edge of truck bed to rear edge of the base rail closest to the Rear Edge of
truck for most vehicle applications (See Fig. 2).
7. Apply the base rail insulator strips (#4) on the bottom of each end of rail correctly to protect aluminum bed from
corrosion as shown in fig.1 & 5. Be sure to cover the entire bottom of the base rail with the base rail insulators.
Center hitch between fender wells and make sure rails are square. Adjust position of rails until both diagonal
measurements are the same. (See Fig. 2 & 3). Position the 5th wheel uprights between the bed rails so that the
tabs in the base of each upright will fit into the slots in the ends of the bed rails. Secure the uprights in place
with the rail hitch pins and hair pins supplied with the 5
member to uprights. On most applications, the 5th wheel assembly should be positioned so that it is
approximately centered over the truck axle and between the wheel wells on the bed floor.
Check for obstructions before drilling. Failure to do so could result in damaged fuel or brake
lines, structural members, etc. HUSKY TOWING PRODUCTS does its best to communicate tow
vehicle manufacturer changes; however, it is ultimately the responsibility of the installer to
All Products limited to Vehicle Tow Rating, see Vehicle Owners Manual. Visit www.huskytow.com for Warranty
Information / Tech Support / Product Updates. ©2018 LKQ SPG. All Rights Reserved. June. 26, 2019-REV7
clearance at the cab and at the bumper to allow for turns.
prevent damage due to installation.
QTY NO
1 8 NYLON TUBE, WEAR RESISTANCE, SHORT
1 9 WASHER, 5/8 Ø.656 ID X Ø1.25 OD X .094 THK
4 10 LOCKWASHER 5/8, Ø.647 ID X Ø1.079 OD X .156 THK
4 11
2 12 BOLT, HEX HEAD 5/8 -11 X 5", GR5, BZ
2 13 BOLT, CARRIAGE, 5/8-11 X 6.00, GR5, BZ
2 14 BOLT, CARRIAGE 5/8-11 X 3-1/2" GR 5, BZ
WARNING:
injury.
CAUTION:
th
wheel installation kit. Securely attach 5th wheel cross
CAUTION:
DESCRIPTION
NUT, HEX 5/8 -11, GR5, ZINC
QTY
2
12
8
8
4
2
2
2