Giordani G-first Instrucciones página 10

G G-F
UK
IORdANI IRsT CAR SEAT
ADJUSTING THE HARNESSES
1. Make sure that the harness
of your car seat is adapted to
the height of your child before
starting to install the seat in
your car.
The harnesses can be adjusted
to 4 different heights and must
be positioned as close as possi-
ble to your child's shoulders (1).
• The two lower positions are
ONLY intended for use in group
0, for a child weighing from 0 to
10 kg in a rear-facing position.
If your child's shoulders are be-
tween two levels in a rearfacing
configuration, choose the lower
of the two.
• The two upper positions are
ONLY intended for use in group
1, for a child weighing from 9 to
18 kg in a front-facing position.
If your child's shoulders are be-
tween two levels in frontfacing
configuration, choose the higher
of the two.
2. To adjust the height of the har-
nesses, remove the upper sec-
tion of one of the harness straps
by pivoting the metal anchor lo-
cated behind the back rest and
then pulling it through the slots
of the shell and cover (2). Repeat
the operation on the upper sec-
tion of the second strap. Feed
the ends of the harness straps
through the slots at identical
level in both the cover and the
shell, according to the chosen
configuration:
• For a rear-facing configura-
(0 - 18 KG)
tion (Gr. 0, from 0 to 10
harnesses are fed through one
of the two lower positions and
then up to the third position to
be secured inside the shell (2
(2 ). Make sure that the metal
B
anchor is correctly positioned
and that the ends of the har-
ness straps are not twisted.
IMPORTANT: Whichever of the
two lower positions you have
chosen, make sure that the met-
al anchors of the harnesses are
well secured through the slots of
the third position of the shell.
• For a front-facing position
1, from 9 to 18 kg), the harness-
es are fed through one of the two
upper positions and are secured
directly behind the position cho-
sen, at the back of the shell (2
(2 ). Make sure that the metal
D
anchor is correctly positioned
and that the ends of the harness
straps are not twisted.
THE CORRECT TYPE OF SAFETY
BELT TO USE WITH YOUR CAR SEAT
3. Your car seat must ONLY
stalled on a passenger seat fitted
with a 3-point safety belt.
install your car seat on a passen-
ger seat fitted with a 2-point safe-
ty belt! (i - 0-10 kg) (i - 9-18kg)
REARWARD FACING USE
(0 - 10 KG)
DO NOT USE THIS CHILD SEAT ON
A PASSENGER SEAT FITTED WITH
AN AIR BAG!
When used rearward facing, the
18
child seat must be in the fully re-
clined position.
kg), the 4. Pull lap and diagonal sections
of the car seat belt until fully ex-
tended and feed both through
the space between the shell and
) the base. Fasten the seat belt.
A
Thread the lap section through
the guides located at the front of
the base (4). Thread the diago-
nal strap through the two upper
guides located on the back of
the seat shell (4
seat belt by pulling first on the
lap section, then on the diagonal
one (4 ). Lock the diagonal sec-
B
tion of the belt with the red lock-
(Gr.
off clip. The lock-off should be
positionned against the buckle
of the seat belt (4
there are no kinks or twists in
the seat belt. Always keep the
) seat in the most reclined posi-
C
tion.
FORWARD FACING USE (9-18KG)
5. Fully recline the seat. Pull lap and
diagonal sections of the car seat
belt until fully extended and feed
both through the space between
be in- the shell and the base. Fasten
the seat belt (5). Feed the waist
NEVER strap of the seat belt through the
guides located under the seat
base of the car seat (5
the child seat right down into the
car seat, and tighten both sec-
tions of the seat belt by pulling
the belt in the direction shown
(5 ). Lock the diagonal section
B
of the belt with the red lock-off
clip. The lock-off should be po-
sitionned against the buckle of
the seat belt (5
there are no kinks or twists in
the seat belt.
HARNESS BUCKLE
6. To fasten the harness, bring the
two shoulder straps together
(6) (6 ) and insert them into the
A
buckle; you should hear a "click"
(6 ). To release the harness,
B
press the buckle's red button
(6 ).
C
). Tighten the
A
FITTING THE HARNESS
7. To tighten the harness: Pull on
the adjusting straps positioned
on the harness. You do not need
to press on the adjuster buttons
(7). IMPORTANT: A correctly ad-
). Check that
C
justed harness is essential for
your child's protection. There
should not be more than finger's
width between the harness and
your child.
Press on the adjuster buttons po-
sitioned on the upper section of
the harness, grasp the lower sec-
tion and pull simultaneously (7
RECLINING YOUR CHILD SEAT
8. Push the adjustment lever locat-
ed under the front of the seat up-
wards, then pull or push the base
towards or away from you (8).
). Push
A
STORAGE OF THE
INSTRUCTION MANUAL
Store this instruction manual, de-
pending on the model of your ve-
hicle, either in the pouch provided,
or by slipping it into between the
shell and the cover of the seat.
19
). Check that
C
To loosen the harness:
).
A