Included In Delivery; Installing The Appliance; Technical Specifications - Bosch BCM 8450 UC Instrucciones De Montaje

Included in delivery

a Fully automatic coffee machine
b Instruction manual
c Installation instructions
d Assembly bracket
e Transformer mount
f Spacers
g 7 fastening screws (silver)
h 2 fastening screws (long/black)
i 2 fastening screws (short/black)
j 1 sleeve (black)
k 2 sleeves (white)
l Quick reference guide
m Measuring spoon
n Water hardness testing strip
o Milk tube (set)
p Milk container
q Suction pipe
r Transformer

Installing the appliance

Make sure there is adequate aeration. To do this, remove
the rear panel or cut out an opening of 19
(500 x 400 mm). There must be a gap of at least 1
between the wall and base of the unit or the rear panel of the
unit situated above. The ventilation slots and intake openings
must not be covered. Also follow the installation instructions for
the appliance situated above or below. If installing the appliance
above a warming drawer, the height of the recess must be 23
(590 mm). If the appliance is installed directly under a décor
panel, ensure that there is a ventilation slot of at least 31 square
inches (200 cm ). The ideal installation height for the fully
2
automatic coffee machine, measured from the floor to the lower
edge of the appliance, is 37
NOTICE:
Installation must always be performed by 2 persons.
1 Unpack all the parts and check for any damage in transit.
Do not operate a damaged appliance.
2 Take note of the installation dimensions of the particular
model.
Important: Two openings angles can be selected for the
door. Depending on the opening angle required, the mounting
distance to the wall should be observed before installation.
● Opening angle approx. 110° (delivery status)
= mounting distance to the wall at least 13
● Opening angle approx. 155°
= mounting distance to the wall at least 25
For an opening angle of 155°, remove both the restrictors at the
top and bottom of the hinge.
3 Remove the installation template on the back of the
installation instructions. Place the installation template at the
front edge of the unit and screw on the assembly bracket d
as shown with two fastening screws g. The assembly
bracket must be positioned at the base of the unit and the
wall such that no gap is present.
4 Fasten the the transformer mount e with two screws g in
the middle.
5 Insert the transformer in the mount. The connections to both
lines must point to the left.
Note: When positioning the transformer r and pushing in the
appliance, do not trap the lines.
The transformer r is not allowed to touch the appliance and
the back wall of the cupboard.
2 en
–
⁄ " x 15 ⁄ "
11 3
16 4
⁄ " (35 mm)
3
8
⁄ " (950 mm).
7
16
⁄ " (350 mm).
3
4
⁄ " (650 mm).
9
16
6 Set the mains switch U to h on the appliance.
7 Securely insert the front line into the appliance (snaps into
place). For this purpose, put the appliance to be plugged
in just on to the edge of the unit. Plug the power cord into
the socket. Plug transformer into dedicated receptacle in an
accessible cabinet adjacent to the coffee maker (depends
on the built-in situation). Do not plug into a receptacle
behind the appliance.
8 Push the appliance into the unit until it clicks into place.
Check that the appliance is in the middle. If necessary,
align the appliance. To do so, pull the appliance out a little,
remove the appropriate spacers f and attach to the left
side (top and bottom). Push the appliance into the unit until
it clicks into place.
9 Take hold of the appliance door on the right next to the
outlet and open. Remove the drip tray Y. Pull the cover X on
the bottom left-hand side forwards and remove. Pull out the
accessories drawer Z and put to one side.
10 First, screw on the appliance as shown using 2 of each
of the fastening screws g and h as well as 2 sleeves k.
Then screw tight at the top right of the unit using 1 fastening
screw g and sleeve j.
11 Only for the expert
In very few cases, the door of the fitted fully automatic
machine can jam due to a warpage in the built-in units. The
door can be adjusted. To do this adjust the hinges at the top
and the bottom.
I. Adjust the depth of the door by turning the screws V.
II. Remove the hinge dampers at the top and bottom of the
hinges. Turn the screws W to adjust the inclination and
⁄ " the horizontal position of the doors.
1
4
III. Re-fit the hinge dampers.
12 Insert the cover X and fix with the two black fastening
screws i.
13 Replace the drip tray Y and accessories drawer Z and close
the appliance door.
Removal
● Undo all screws.
● Slightly pull out the appliance.
● Remove the power cord from the socket.
● Disconnect the appliance from the transformer.
● Fully remove the appliance.

Technical specifications

Power connection
with transformer type 8001007072
(voltage – frequency)
Heater wattage
Maximum static pump pressure
Maximum water tank capacity
(without filter)
Maximum capacity of the
coffee bean container
Length of power cable
(Power socket – transformer)
Dimensions
(appliance without transformer)
H x B x D
Weight, empty
(appliance without transformer)
Dimensions (only transformer)
H x B x D
Weight (only transformer)
Type of grinding unit
120 V AC – 60 Hz
1600 W
19 bar
81,15 oz (2.4 l)
17,64 oz (500 g)
39" (1 m)
17.91 x 23.39 x 14.76"
(455 x 594 x 375 mm)
42-44 lb (19-20 kg)
8,26 x 6,77 x 7,80"
(210 x 172 x 198 mm)
27,55 lb (12,5 kg)
Ceramic