cleanAIR CA-5 Manual De Usuario página 7

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 49
The CA – 20 hood can only be combined with
approved ADF 110 x 110 mm in size! - see the list
of parts and accessories.
For more information and recommendations see
the enclosed manual from the manufacturer.
5.7. Welding hood CA – 22
A protection polycarbonate foil 0.75 mm thick
is available for protection of the ADF. The foil
is fitted from both the outer and inner side of
the cartridge and prevents spray balls from
sticking to the visor. The inner foil is inserted
straight in the cartridge, the outer one is to be
inserted in front of the ADF in the hood frame.
Before installing protective foils, peel off the
thin cover films from their both sides.
Always use protection foils in welding hoods,
otherwise the ADF will be damaged during
welding!
Material: Visor – polycarbonate
Face seal
retardant – face seals must not be washed!
Hood – see the manufacturer's
manual
5.7.1. Face seal replacement:
Removing the face seal:
Release the face seal from the velcro
fasteners on the headband.
Unscrew the headband nuts.
Remove the headband. It is fixed to
the air duct with a velcro fastening.
Remove the air duct by pulling through
out of the face seal hole.
Remove the face seal. Release it by
pulling from the velcro fastening on the hood
shell.
Carry out this operation carefully so as
not to unstick also the velcro fastener.
Putting on the face seal:
Start in the middle of the lower edge
and fix the face seal symmetrically along the
circumference to the hook-and-look fastening
on the inner side of hood.
Pull the air duct through the face seal
and screw in the headband.
Fix the face seal with the side straps to
the headband.
– cotton with flame
For hygiene reasons, discard the old face seal
immediately after replacement so that it cannot
be reused. The face seal must not be washed!
Washing
causes
loss
impregnation securing incombustibility!!!
5.7.2. Protection foil replacement
We recommend using protection foils for all
CleanAIR hoods. The foil protects the hood
visor and prevents it from damaging and
soiling. An early replacement of foils extends
the hood life, provides a continuously good
through view and makes work easier.
Warning: Do not clean foils dry, otherwise they
may be scratched easily and their transparency
will be reduced. Foils can also concentrate
electrostatic discharges and, therefore, the
through view may be reduced in a dusty
environment.
5.7.3. Forehead strap replacement:
The
soft
forehead
headband prevents pressure damage and
increases comfort during use. Replace it as
necessary; it can be unfastened easily owing
to its fixing with a velcro fastening.
The CA – 22 hood can only be combined with
approved filters 90 x 110 mm in size! - see the list
of parts and accessories.
5.8. Safety helmet with welding hood CA –
40
For
this
helmet
protection, its size must be adjusted to the
user's head size (54 - 65 cm). Make sure that
the helmet sits on the head comfortably, but
firmly. If the helmet is not in use or during
transport it should be stored in a package
protecting it against direct sunlight, chemicals
and abrasive agents and in which it cannot be
damaged
by
its
objects/surfaces.
With regard to the fact that the helmet will only
be supplied in a combination with a welding
shield, the function of the chin strap of the
helmet is replaced with a face seal and,
therefore, there is neither a chin strap nor
fastenings for the chin strap on the helmet.
Welding cartridges made of hardened mineral
glass may only be used in connection with
appropriate inner protection foils!
of
the
protective
strap
embracing
to
provide
appropriate
contact
with
the
hard

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ca-1Ca-2Ca-3Ca-4Ca-10Ca-20 ... Mostrar todo

Tabla de contenido