BMW DWA V Instrucciones De Montaje página 28

Plugs on the base module:
Plug (1), black, 15-pin
Plug (2), yellow/violet, 26-pin
Plug (3), green, 26-pin
Base module (4)
Plug (5), black, 18-pin
Connections to plug (1), black, 15-pin X13252
A15 Connect terminal 30 branch, cable colour
red/white, to the cable on pin 10, cable colour
red/green/yellow.
Connections to plug (2), yellow or violet,
26-pin X13253
A17 Connect the central locking branch (lock),
cable colour yellow/blue, to pin 17 or to the
cable, cable colour white/red/yellow.
A18 Connect the central locking branch (open),
cable colour green/blue, to pin 4, cable colour
blue/red/yellow (adapter cable), or to the
cable, cable colour blue/red/yellow.
B5 Connect the central locking branch
(synchronisation open), cable colour white/green,
to the cable on pin 1, cable colour white/green.
Connections to plug (3), green 26-pin X13254
A1 Connect the front left-hand door contact
switch branch, cable colour brown/grey,
to the cable on pin 2, cable colour
brown/grey/yellow.
B4 Connect the front right-hand door contact
switch branch, cable colour brown/blue,
to the cable on pin 3, cable colour
brown/blue/yellow.
Cars from Series E 36/3/4 with base module only
F 36 82 160
A23 Cut the rear right-hand door contact switch,
cable colour brown/black, pin 4 and strip both
ends. Cut the rear left-hand door contact
switch, cable colour brown/white, pin 5 and strip
both ends. Crimp together cables (1) (pin 4)
and (2) (pin 5), coming from plug X13254 with
a contact socket. Connect a socket casing.
Crimp together cables (1) and (2), coming from
the standard wiring harness with a pin contact
and connect a plug casing. Connect branch A23
door contact switch at the rear.
Cars from Series E 36 with base module only
F 36 82 152
There is one joint connector with a cable
colour of violet/white and one joint connector
with a cable colour of white/violet.
It must be ensured that in ignition key position I
(terminal 75), there is battery voltage at branch A5,
if necessary test this using a multimeter.
28
= X13252
= X13253
= X13254
= A104
= X10182
A5 Connect the terminal 75 branch, cable colour
violet/white, to joint connect X1235 (1), cable
colour violet/white or to the black 6-pin plug
X322, pin 2, cable colour violet/white.
All cars
F 36 62 088
A6 Connect the terminal 31 branch (1), cable
colour brown, to the ground post X1166,
on the passenger side (2) under the carpet.
F 36 62 085
A16 Connect the hazard lights system branch
(hazard lights system controller), cable colour
blue/red, to the black 5-pin plug X516 (1),
pin 2, cable colour brown/blue.
Cars from Series E 36/2/4 only
F 36 62 090
A22 Remove the boot contact switch branch cover
at the rear left-hand side of the boot, select
the cable, cable colour brown/white, and
connect it or remove the boot contact switch,
crimp the contact (1) to the boot contact
switch branch, connect it to the boot contact
switch (3) using the standard cable (2) and
install the boot contact switch (3).
Cars from Series E 36/5 with central locking
module only
F 36 62 282
A22 Lay the boot contact switch branch, cable
colour brown/white, on the right-hand side
of the car along the vehicle wiring harness
towards the rear to the right-hand tail light.
Disconnect the black 8-pin plug (1) from the
tail light unit (2). Release the plug (1) and
disconnect the cable to pin 3 or 4 (depending
on model year), cable colour brown/white.
Crimp branch A22 to the bridge cable (4) and
connect it to pin 3 or 4. Connect the cable (3),
cable colour brown/white, to the bridge
cable (4) using a 1-pin plug.
Cars from Series E 36/5 with base module only
F 36 0002 2W
A22 Lay the boot contact switch branch (4), cable
colour brown/white, to the base module (1).
Cut the cable to the required length.
Fit the cable with a twin lead terminal.
Cut the brown/white cable (3) from the plug (2)
X13254, pin 4. Crimp on a plug or socket
casing and install the casing. Connect up
branch A22 (4).
Cars from Series E 36/3 only
F 36 82 523 R
Lay the branch (1), cable colour
A22
brown/white, along the vehicle wiring
harness to the rear left backrest. Cut and
strip the brown/white cable on the vehicle