Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
B
OUTSIDE TOP EXHAUST
INSTALLATION OVERVIEW
B1. Attach Mounting Plate to Wall
B2. Prepare Top Cabinet
B3. Check Motor Orientation
B4. Adapting For Outside Ventilation
B5. Assemble and Install Adaptor
B6. Mount the Microwave
B7. Adjust The Exhaust Adaptor
B8. Connecting Duckwork
ATTACH THE MOUNTING PLATE
B1
TO THE WALL
Attach the plate to the wall using toggle bolts and
wood screws. At least one wood screw must be used
to attach the plate to a wall stud..
Remove the toggle wings from the bolts.
1
Insert the bolts into the mounting plate through
2
the holes designated to go into drywall and reattach
the toggle wings to
16
Installation Instructions
OPTION 1
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE::
D O NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
D
B
IMPORTANT: Do NOT remove the
cardboard spacers between the heat
shield and door
3 4
(Vertical Duct)
3/8" TO EDGE
OPTION 2
STEP 1:
Installer uses bracket to make 2 marks. First
12"
mark is made by using the stampled slot in bracket.
Second mark is made on the ouside edge of bracket.
F. CUT OUT FOR HORIZONTAL
Horizontal line
4"
OUTSIDE EXHAUST
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
Make a mark
Make a mark here, along
STEP 4:
even with
here,
inside bottom of the
bottom of
stamped slot provided.
stamped
slot
STEP 2:
Installer moves bracket to the other side of
the cabinets and makes 2 more marks. Marks are the
same as STEP 1, just opposite side.
Make a
Make a mark here, along
mark here,
inside bottom of the
bottom of
even with
stamped slot provided
stamped
(same as Step 1).
slot
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
NOTES:
- 13" Max Cabinet Depth
30" MINIMUM WIDTH REQUIRED
- 15" deep cabinets require additional steps using
an additional installation kit: JX36BUMP
REAR WALL TEMPLATE
C
A
C
To use toggle bolts:
Mounting
Plate
Insert the toggle wings into the holes in the wall and
3
place the mounting plate against the wall.
CAUTION
fingers between the back of the mounting plate and
the wall.
4
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
Spacing for Toggles More
Than Wall Thickness
Toggle Wings
Toggle
Bolt
Wall
Bolt End
Mounting Plate
Be careful to avoid pinching
31-7000110 Rev. 1
Publicidad
Tabla de contenido
