General Safety Information - STA-RITE DC13318V Manual Del Usuario

Safety • Specifications
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual
contains important instructions that should be
followed during installation, operation, and
maintenance of the product. Save this manual
for future reference.
This is the safety alert symbol. When you
see this symbol on your pump or in this manual,
look for one of the following signal words and
be alert to the potential for personal injury!
indicates a hazard which, if not
avoided, will result in death or serious injury.
indicates a hazard which, if not
avoided, could result in death or serious injury.
indicates a hazard which,
if not avoided, could result in minor or
moderate injury.
NOTICE addresses practices not related to
personal injury.
Description
This submersible sump pump is designed for
home sumps. Unit is equipped with a 3-prong
grounding-type power cord. Shaded-pole motor
is oil filled and sealed for cooler running. Sleeve
bearings on motor shaft never need lubrication.
Automatic reset thermal protection.
Specifications
Power supply required .................................. 115V, 60 HZ.
Liquid Temp. Range ......................... 32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ............15 Amps
Discharge: ...................................................... 1-1/2" FNPT
NOTICE: This unit is not designed for
applications involving salt water or brine! Use
with salt water or brine will void warranty.
Pump water only with this pump.
Do not use where water recirculates.
Not designed as a swimming pool drainer.
Performance
Total Feet (m) of Lift
Model 5 (1.5) 10 (3)
Capacity Gallons/Hour (L/H)
2,760 2,200
DC13318V
(10,448) (8,328)
3,200 2,700
DC15018T
(12,113) (10,221)
15 (4.6) 20 (6.1) No flow at
height shown
below
1,400 20'
-
(5,299) (6.1 m)
2,000 1,200 24'
(7,571) (4,542) (7.3 m)
Electrical & Switch Specifications
Individual
Motor
Model
HP
DC13318V 1/3
DC15018T 1/2

General Safety Information

Electrically powered sump pumps normally
give many years of trouble-free service when
correctly installed, maintained, and used.
However, unusual circumstances (interruption
of power to the pump, dirt/debris in the sump,
flooding that exceeds the pump's capacity,
electrical or mechanical failure in the pump,
etc.) may prevent your pump from functioning
normally. To prevent possible water damage
due to flooding, consult your retailer about
a secondary AC sump pump, a DC backup
sump pump, and/or a high water alarm. See
Troubleshooting in this manual for information
about common sump pump problems
and remedies. For more information, see your
retailer, call customer service at 1-888-782-7483
or visit our website at Sta-Rite.com.
1. Know the pump application, limitations, and
potential hazards.
2. Do not use in water with fish present.
3. Disconnect power before servicing.
4. Release all pressure within system before
servicing any component.
5. Drain all water from system before servicing.
6. Secure discharge line before starting pump.
An unsecured discharge line will whip,
possibly causing personal injury and/or
property damage.
7. Check hoses for weak or worn condition
before each use, making certain that all
connections are secure.
8. Periodically inspect sump, pump and system
components. Keep free of debris and foreign
objects. Perform routine maintenance
as required.
9. Provide means of pressure relief for pumps
whose discharge line can be shut-off
or obstructed.
*Switch Setting in inches
Branch
Water Level For:
Circuit
Req.
On
(Amps)
7.5"
(19.1 cm)
15
13"
(33 cm)
2
Off
3"
(7.6 cm)
6"
(15.2 cm)