Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Vent housing • D) (4) 1/2" screws • E) (4) Panel clips
A
B
Metra. The World's Best Kits.
®
Ford Mustang
Visit
MetraOnline.com
for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DDIN radio provision
• Painted matte black
C
MetraOnline.com
1994-2000
D
E
© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION
95-5703B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Visit metraonline.com for audio and steering
wheel interface options.
Antenna Adapter: Not required
TOOLS REQUIRED
• 1/8" drill bit• Cutting tool
• Ford radio removal tools* • Phillips screwdriver
• T-20 Torx screwdriver
* Metra part number 86-5618
Attention!
With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
REV. 7/19/21 INST95-5703B
Publicidad
Tabla de contenido
Manuales relacionados para Metra 95-5703B
Resumen de contenidos para Metra 95-5703B
- Página 1 Ensure that all installation connections are secure before cycling the ignition to test this product. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/19/21 INST95-5703B...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Unclip, unplug, and remove the trim panel surrounding the shifter. (Figure A) 2. Using Metra’s 86-5618 radio removal tools (sold separately), release the radio from the dash. Slide the radio out, then unplug and remove the radio. If the vehicle is equipped with a CD player below, remove in the same manner. -
Página 3: Kit Preparation
KIT PREPARATION KIT ASSEMBLY To the 95-5703B radio trim panel: 1. Secure the radio brackets to the radio using the screws supplied with the radio. 1. Attach the factory a/c vents removed in (Figure A) Dash Disassembly to the vent housing. - Página 4 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/19/21 INST95-5703B...
- Página 5 • Broca de 1/8 • Herramienta de corte • Herramientas de retiro de radio Ford* • Destornillador Phillips • Destornillador Torx T-20 * Número de pieza Metra 86-5618 ¡Atención! Deje que el vehículo se asiente con la llave fuera del encendido durante unos minutos antes de quitar la radio de fábrica.
-
Página 6: Desmontaje Del Tablero
(Figura A) 2. Saque el radio del tablero usando las herramientas de retiro de radio de Metra 86-5618 (se venden por separado). Deslice el radio hacia afuera y, después, desconéctelo y quítelo. Si el vehículo está... -
Página 7: Preparación Del Kit
PREPARACIÓN DEL KIT ENSAMBLE DEL KIT Al panel de moldura de radio 95-5703B: 1. Sujete los soportes del radio al radio usando los tornillos que vienen incluidos 1. Fije las rejillas de aire acondicionado de con el radio. (Figura A) fábrica que quitó... - Página 8 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recomienda MECP técnicos certificados Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/19/21 INST95-5703B...