Metra 95-5701 Manual De Instrucciones
  1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Accesorios de Automóviles
  5. 95-5701
  6. Manual de instrucciones

Metra 95-5701 Manual De Instrucciones

F serie trucks 1992-1996; bronco 1992-1996; f250 1997; f350 1997
Ocultar thumbs
1
2
3
4
5
6
7
8
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C (2) Panel clips
A
B
Metra. The World's Best Kits.
®
Ford
F-Series Trucks
Bronco
1992-1996
F250/350
1997
KIT FEATURES
• ISO DDIN radio provision
C
MetraOnline.com
1992-1996
© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION
95-5701
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Preparation . ......................................................3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Visit metraonline.com for audio/
video and steering wheel control interface options.
Antenna Adapter: Not required
TOOLS REQUIRED
Ford radio removal tools* • Phillips screwdriver
• Cutting tool
* Metra part number 86-5618
Attention!
With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
REV. 7/16/21 INST99-5701

Publicidad

Tabla de contenido
loading

Manuales relacionados para Metra 95-5701

Resumen de contenidos para Metra 95-5701

  • Página 1 Ensure that all installation connections are secure before cycling the ignition to test this product. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/16/21 INST99-5701...

  • Página 2: Dash Disassembly

    DASH DISASSEMBLY 1. Using Metra’s 86-5618 radio removal tools (sold separately), release the radio from the dash. Slide the radio out, then unplug and remove the radio. (Figure A) 2. Unclip and remove the trim panel between the radio and climate controls. (Figure B) 3. Unclip and remove the climate control trim panel. (Figure C) (Figure A) (Figure B) (Figure C) Continue to Kit Preparation 386.257.1187 MetraOnline.com...

  • Página 3: Kit Preparation

    1. Cut the sub-dash and factory trim panel 1. Secure the radio brackets to the radio to allow room for the radio assembly. using the screws supplied with the Note: See detail for proper cut in area radio. (Figure A) indicated. (Figures A, B) 2. Locate the factory wiring harness and Remove shaded areas 2. Cut and remove the radio support brace antenna connector in the dash and in the top of the sub-dash. complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test Continue to Kit Assembly the radio for proper operation. 3. Remove the upper (2) 9/32” screws securing the climate controls. Secure (Figure A) (Figure A) the radio assembly to the dash using Detail the climate control screws. 4. Attach the (2) clips provided onto the 95-5701 radio trim panel. Clip the panel Remove shaded area onto the dash and radio brackets to complete the installation. (Figure B) (Figure B) (Figure B) REV. 7/16/2021 INST99-3024B...
  • Página 4 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/16/21 INST99-5701...
  • Página 5 • A) Panel de moldura para radio • B) Soportes del radio • C) Ganchos para panel HERRAMIENTAS NECESARIAS • Herramientas de retiro de radio Ford* • Destornillador Phillips • Herramienta de corte * Número de pieza Metra 86-5618 ¡Atención! Deje que el vehículo se asiente con la llave fuera del encendido durante unos minutos antes de quitar la radio de fábrica.

  • Página 6: Desmontaje Del Tablero

    DESMONTAJE DEL TABLERO 1. Saque el radio del tablero usando las herramientas de retiro de radio de Metra 86-5618 (se venden por separado). Deslice el radio hacia afuera y, después, desconéctelo y quítelo. (Figura A) 2. Desenganche y quite el panel de moldura que se encuentra entre el radio y los controles de clima.

  • Página 7: Preparación Del Kit

    4. Fije los (2) ganchos que se incluyen en Quite las áreas sombreadas el panel de moldura de radio 95-5701. Enganche el panel al tablero y los soportes de radio para terminar la instalación.
  • Página 8 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recomienda MECP técnicos certificados Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/12/21 INST95-5701...

Tabla de contenido