Meaning Of Symbols; Preparation For Operation; Battery Charging - GRAPHITE 58G014 Manual De Instrucciones

The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is
always a small risk of injuries at work.
Li-Ion batteries may leak, set on fire or explode when
heated to high temperature or short-circuited. Do not store
the batteries in a car in hot and sunny days. Do not open
the battery. Li-Ion batteries contain electronic protection
devices that, if damaged, may cause fire or explosion of the
battery.
Explanation of used symbols
2
1
6
5
10
9
Read instruction manual, observe warnings and safety
1.
conditions therein.
Use protective goggles and hearing protectors.
2.
Work with protective mask on.
3.
Keep the tool away from children.
4.
Protect against rain.
5.
Use indoors, protect from water and moisture.
6.
Recycling.
7.
Protection class 2.
8.
Segregated waste collection.
9.
Do not throw cells into fire.
10.
Hazardous to water environment.
11.
Do not allow to heat above 50°C.
12.
CONSTRUCTION AND USE
Orbital sander is a battery-powered tool. The drive consists of
DC commutator motor with permanent magnets. Orbital sander
is designed for sanding and polishing surfaces of wood, metal,
plastic and similar materials, with the use of sanding paper with
appropriate gradation. Range of use covers repair and building
works, and any work from the range of individual, amateur
activities (tinkering).
Do not use the sander for sanding surfaces that contain
magnesium or asbestos, or covered with gypsum.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on
the drawing pages of this manual.
Off switch
1.
On switch
2.
Dust bag
3.
Dust extraction outlet
4.
Backing pad
5.
Battery lock button
6.
Battery
7.
Charger
8.
4
3
8
7
Max.
50°C
11 12
13
LED diodes
9.
Button for battery level indication
10.
Battery level indicator (LED)
11.
* Differences may appear between the product and drawing.

MEANING OF SYMBOLS

CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Dust bag - 1 pce
1.
Abrasive paper - 1 pce
2.

PREPARATION FOR OPERATION

REMOVING AND INSERTING THE BATTERY
• Push battery lock button (6) and slide out the battery (7)
(fig. A).
• Insert charged battery (7) into the handle holder, you should
hear when the battery lock button (6) snaps.

BATTERY CHARGING

The device is supplied with partially charged battery. The battery
should be charged in ambient temperature between 4°C and
40°C. New battery, or one that has not been used for a long
time, will reach full efficiency after approximately 3 to 5 charge/
discharge cycles.
• Remove the battery (7) from the device (fig. A).
• Connect the charger to mains socket (230 V AC).
• Slide the battery (7) into the charger (8) (fig. B). Ensure the
battery is properly fitted (pushed to the end).
When the charger is connected to a mains socket (230 V AC), the
green diode (9) on the charger turns on to indicate connected
supply.
When the battery (7) is placed in the charger (8), the red diode
(9) on the charger turns on to indicate that the charging is in
progress.
At the same time green diodes (11) of the battery level indication
are flashing in different configurations, see description below.
• All diodes are flashing - battery is empty and requires
charging.
• 2 diodes are flashing - the battery is partially discharged.
• 1 diode is flashing - the battery level is high.
Once the battery is charged, the diode (9) on the charger lights
green, and all battery level diodes (11) light continuously. After
some time (approx. 15 s) battery level indication diodes (11) turn
off.
Do not charge the battery for more than 8 hours. Exceeding
this time limit may cause damage to battery cells. The charger
will not turn off automatically when the battery is full. Green
diode on the charger will remain on. Battery level indication
diodes turn off after some time. Disconnect power supply
before removing the battery from the charger socket. Avoid
consecutive short chargings. Do not charge the battery after
short use of the tool. Significant decrease of the period
between chargings indicates the battery is worn out up and
should be replaced.