Spark Plug Maintenance; Transportation And Storage; Storing The Product - Ryobi RLM46160S Traduction Des Instructions Originales

disposal site. See your local oil retailer for more information.

SPARK PLUG MAINTENANCE

See fig. 12
The spark plug must be properly gapped and free of
deposits in order to ensure proper engine operation. To
check:
■ Stop the product. Make sure that all moving parts have
come to a complete stop. Allow the product to cool
down. Disconnect the spark plug wire.
■ Remove spark plug boot.
■ Clean any dirt from around base of spark plug.
■ Remove spark plug using a 13/16 in. spark plug socket
(not provided).
■ Inspect spark plug for damage, and clean with a wire
brush before reinstalling. If insulator is cracked or
chipped, spark plug should be replaced.
NOTE: The recommended spark plug models are
TORCH F7RTC or NGK BPR6ES.
■ Measure plug gap. The correct gap is 0.71 mm −
0.79 mm. To widen gap, if necessary, carefully bend
the ground (top) electrode. To lessen gap, gently tap
ground electrode on a hard surface.
■ Seat spark plug in position; thread in by hand to prevent
cross-threading.
■ Tighten with wrench to compress washer. If spark plug
is new, use 1/2 turn to compress washer appropriate
amount. If reusing old spark plug, use 1/8 to 1/4 turn for
proper washer compression.
NOTE: An improperly tightened spark plug will become
very hot and could damage the engine.
■ Reinstall spark plug boot.
DRIVE GEAR MAINTENANCE
See fig. 15
To ensure smooth operation of the wheels, the wheel
assembly should be cleaned before storage.
■ Remove the spat (hub cap).
■ Remove the nut and wheel and set aside.
■ Remove the e-ring, pins, and wheel gear. Clean any
dirt from these items and the end of the drive shaft by
wiping with a dry cloth. If necessary, rubbing alcohol
may be used to remove any stubborn dirt.
CAUTION: Do not lubricate any of the wheel components
Lubrication may cause the wheel components to fail during
use, which could result in mower damage.
■ Reinstall the wheel gear with the arrows facing the front
of the mower. Reinstall the pins and e-ring.
■ Reinstall the wheel and nut. Tighten nut to secure.
■ Assemble the spat (hub cap).
REPLACING WHEELS
See fig. 16
8
WARNING
Use only the manufacturer's replacement wheels. Using
wheels that are not approved by the manufacturer is
hazardous and could result in serious personal injury.
■ Stop the product. Make sure that all moving parts have
come to a complete stop. Allow the product to cool
down. Disconnect the spark plug wire.
■ Remove the spat (hub cap).
■ Remove the nut from the wheel axle, then remove the
wheel.
■ Replace with new wheel and reinstall nut to secure.
■ Assemble the spat (hub cap).

TRANSPORTATION AND STORAGE

STORING THE PRODUCT

When storing the mower for 30 days or more:
■ If using a fuel stabilizer, follow the stabilizer
manufacturer's directions to add stabilizer to petrol in
the fuel tank. Run the engine at least 10 minutes after
adding stabilizer to allow the stabilizer to reach the
carburettor.
WARNING
Do not store the product with petrol in the tank inside a
building where fumes may reach an open fl ame or spark.
■ If not using a fuel stabilizer, allow the engine to run until
the product is completely out of fuel.
■ Once the engine has stopped, allow the blade to come
to a complete stop and disconnect the spark plug wire.
■ Turn the fuel valve to the closed position.
■ Turn the product on its side (with carburettor facing up)
and clean grass clippings that have accumulated on the
underside of the mower deck.
■ Clean the underside of the mower deck.
■ Wipe the product clean with a dry cloth.
■ Check all nuts, bolts, knobs, screws, and fasteners for
tightness.
■ Inspect moving parts for damage, breakage, and wear.
Have repairs made on any damaged or missing parts.
■ Store the product in a well-ventilated area that is clean,
dry, and is out of the reach of children.
■ Do not store near corrosive materials, such as fertilizer
or rock salt.
To lower the handle before storing
See fig. 3
■ Loosen the starter rope guide knob. Remove starter
rope from guide and allow to retract into engine.
English