Zoeller Z Control Apak 10-4013-A Instrucciones De Instalación página 2

Manufacturer warrants, to the purchaser and subsequent owner during
the warranty period, every new product to be free from defects in material
and workmanship under normal use and service, when properly used and
maintained, for a period of 5 years from date of purchase by the end user. Parts
that fail within the warranty period, that inspections determine to be defective
in material or workmanship, will be repaired, replaced or remanufactured at
Manufacturer's option, provided however, that by so doing we will not be
obligated to replace an entire assembly, the entire mechanism or the complete
unit. No allowance will be made for shipping charges, damages, labor or
other charges that may occur due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any
material or product that has been disassembled without prior approval of
Manufacturer, subjected to misuse, misapplication, neglect, alteration, accident
or uncontrollable act of nature; that has not been installed, operated or
maintained in accordance with Manufacturer's installation instructions; that has
been exposed to outside substances including but not limited to the following:
sand, gravel, cement, mud, tar, hydrocarbons, hydrocarbon derivatives (oil,
gasoline, solvents, etc.), or other abrasive or corrosive substances, wash towels
or feminine sanitary products, etc. in all pumping applications. The warranty
DO NOT install sensor in direct line of incoming liquid.
1) Fasten sensor to right-angle mounting bracket by unthreading plastic nut. Re-tighten plastic nut after inserting sensor stem in bracket (see Figure C).
2) Locate sensor at desired activation level and secure mounting bracket to the discharge pipe as shown (see Figures C, D, and E) using supplied hose clamp.
NOTE: DO NOT install cord under hose clamp.
3) Secure sensor cord to discharge pipe. Be sure not to leave any loose cord that could rub against and obstruct other devices in basin assembly.
NOTE: Create a cable strain relief when securing the control switch cord by fastening a 2" (50 mm) loop of the cord to the pipe with a cable tie or tape. Be sure
sensor float moves up and down without interference.
CLAMP & BRACKET DETAIL
Figure C
NOTE: Alarm system 10-4014 is recommended for sewage applications. If a 10-4013 is used in a sewage
application, the float should be inspected and cleaned as necessary after any high water incident.
1) Place cord into clamp and secure to discharge pipe as shown in clamp detail (see Figure F). NOTE: Do not install the cord under the hose clamp.
2) Tighten the hose clamp with a screwdriver. NOTE: Do not over tighten; over-tightening may cause damage to the plastic clamp.
3) Make sure the float cable is not allowed to touch the excess hose clamp band during operation.
4) The float switch must be suspended 7" (17.8 cm) below desired activation level (see Figure G).
5) Be certain that installation of float allows for unobstructed range of motion.
LIFT PUMP
Suspend control switch above pump turn on level. If a pump failure causes high-level condition, the APak
HOLDING TANK
Suspend control switch into tank 7" (17.8 cm) below desired alarm level. APak
LIMITED WARRANTY
CONTROL SWITCH INSTALLATION
VERTICAL REED SENSOR
(10-4013)
CONTROL SWITCH
NORMALLY OPEN
ALARM
LEVEL
SK1301E
MECHANICAL FLOAT SWITCH
(10-4014)
© Copyright 2018 Zoeller
set out in the paragraph above is in lieu of all other warranties expressed or
implied; and we do not authorize any representative or other person to assume
for us any other liability in connection with our products.
Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky 40211,
Attention: Customer Support Department to obtain any needed repair or
replacement of part(s) or additional information pertaining to our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH
OF EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OF
MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE
EXPRESSED WARRANTY.
Some states do not allow limitations on the duration of an implied warranty,
so the above limitation may not apply to you. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
SK1301D
Figure D
Alarm System will activate (see Figure A).
®
Alarm System will activate if float ascends to alarm level (see Figure G).
®
Co. All rights reserved.
®
2
SK1301E
Figure E