Maintenance, Cleaning And Storage; Spin On An Increasing Element; Spin On A Ground Spike; Spin In Hanger - höfats SPIN Manual Del Usuario

"Opening of the combustion gel can", "Lighting", "Putting on the glass
cylinder", "During operation", "Extinguishing".

2. Maintenance, cleaning and storage

SPIN is made of high-quality materials. In order to clean and care the
surfaces, please observe the following instructions:
When the flames are extinct, let SPIN cool off completely
before cleaning.
The glass cylinder is made of high-quality borosilicate glass and can
easily be cleaned with a soft cloth and some soap. Rinse thoroughly and
remove all soap residues before drying the glass. Soap residues can
increase the risk that soot particles set down on the glass.
For the main unit, neither strong or abrasive solvents nor scrub pads
must be used. These would attack the surface and leave scrape marks.
A wet, soft cloth with a pH-neutral cleaning agent is sufficient in order to
clean the main unit.
Always keep SPIN at a well-protected place and never expose SPIN to
harsh weather conditions.
The stainless steel refill cup be conveniently cleaned in the dishwasher.
We recommend using a washing program of min. 60°C.

3. SPIN on an increasing element

It is also possible to use SPIN with an increasing element. With this
application, SPIN can be used in increased position on the ground. The
increasing element is simply screwed between footing and main unit.
Important: a maximum of one increasing element is allowed. SPIN in
increased position must only be operated outdoors.

4. SPIN on a ground spike

• You can also use SPIN in combination with a ground spike. This turns
SPIN into an exciting fire display for your outdoor areas. Simply
unscrew the main component from the stand and screw it onto the
ground spike (without elevation mount). Please refer to the quick
guide.
• The three-part ground spike makes SPIN a versatile garden torch. The
different lengths of the three pole components (48 cm / 34 cm / 17
cm) can be used individually or in combination to create the following
overall lengths: 99 cm, 82 cm, 65 cm, 48 cm, 34 cm, 17cm.
• When paired with the ground spike, SPIN is only suitable for outdoor
use.
• It is essential to drive the ground spike deeply into the ground – we
recommend driving the spear pint at least 25cm into the ground. Make
sure that the ground spike is firm and stable. The insertion depth can
vary depending on soil texture. If the soil is particularly soft & loose,
you may not be able to safely insert the ground spike. If you cannot
ensure that the ground spike will stand securely SPIN may not be
used. Always maintain the necessary safety distances from flammable
well-ventila-
outdoors ted rooms
in a car /
motorhome
in a tent
materials (see point 1.4)
• Alternatively, SPIN ground spike / SPIN torch can also be set up with
the separately available stand (Ø 230 mm, Art. No. 0007). The base of
the table variant (Ø 190 mm) is expressly not suitable for use with the
ground spike / torch. When using the stand, it must be ensured that it
is placed on a firm surface, such as a B. terrace floor or pavement is
placed.

5. SPIN in hanger

SPIN can be transformed into a beautifully shaped hanging lantern with
the help of the hanger. This allows SPIN to be suspended freely from
a ceiling or similar. To do this, screw the main body, without the foot
part, into the frame of the hanger. AN ELEVATION MUST NOT BE USED
UNDER ANY CIRCUMSTANCES. Observe the brief instructions for SPIN
hanging fire.
• SPIN can be adjusted to the desired height with the help of the
continuously adjustable stainless steel cable. To do this, simply open
the Allen screw on the clamping element. When retightening the
screw, make sure that there is sufficient clamping force. The easiest
way to do this is to pull on the lower end of the frame.
• Make sure that the stainless steel cable is not kinked, otherwise
permanent deformation may occur.
• The height adjustment of SPIN hanging fire must always be done
without the glass tube.
• To securely fasten SPIN hanging fire to a ceiling or similar, we
recommend the use of screw hooks or ceiling hooks with min. Ø 6 mm.
Depending on the nature of the surface, the appropriate fixing material
(e.g. dowels with ceiling hooks) must be selected. Make sure that the
screw hook/ceiling hook has sufficient hold in the substrate. The hook
should be able to withstand a tensile force of at least 60 kg. Consult a
professional about the correct fastening technique and design for your
specific application.
• When attaching the fastening hoe, make sure that there is sufficient
safety distance to flammable, easily combustible materials. A safety
distance of min. 60cm in all directions must be ensured.
• SPIN hanging fire must only be done when cold, never move the product
when hot. The glass tube must always be removed when hanging and
suspending, the glass tube could fall down and break.
• SPIN hanging fire may only be installed in wind-protected locations to
prevent uncontrolled swinging of SPIN. Depending on the length of the
steel cable, the pendulum swing can be very large.
• When operating SPIN hanging fire, always ensure that no pendulum
movement occurs. If a pendulum movement should occur, SPIN
hanging fire must be returned to the rest position as quickly as
possible. Always use heat-resistant gloves, there is a risk of burns
from hot components.
• Make sure that all components are securely fastened before ignition
and commissioning. The wing body must be firmly screwed onto the
bracket.
well-ventila-
outdoors ted rooms
in a car /
motorhome
in a tent