Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Customer Assistance - Bosch PSE 180 E Manual Del Usuario

Ocultar thumbs Ver también para PSE 180 E:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21
OBJ_BUCH-746-002.book Page 14 Tuesday, June 19, 2012 9:26 AM
14 | English
Special Application Tools
Universal Blade
SM 35 CS (2 608 691 098)
Steel, 35 mm, narrow, extra-sharp
especially for removing putty from window
joints or remainders from door rabbets
Groove Scraper
SD 3 HM (2 608 691 112)
Carbide, 3 mm, narrow, with plastic tile-protec-
tor
e.g. for removing of tiling grout from tile joints
Holder for Bosch Replacement Blades
SD 45 C (2 608 691 104)
Bosch Replacement Blades (45 mm)
SD 45 CE (2 608 691 140)
e.g. for removing paint and silicone remainders
from sensitive surfaces such as tiles and glass
Wear protective gloves when handling re-
placement blades!
Staple Remover
SD 8 C (2 608 691 116)
Steel, 8 mm, narrow
e.g. for removing staples and decoration nails
out of soft wood
Note: The staples are removed by the stroke
motion of the power tool. Do not use the power
tool for levering off!

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the application tools from adhesive and debris remain-
ders each time after using.
Replacing the Dust Protection Cap
The dust protection cap 3 prevents the penetration of dust
and debris into the tool holder 2 and additionally serves as a
no-load stroke stop.
2 609 932 850 | (19.6.12)
The dust protection cap 3 can wear off with time. Replace a
damaged or worn dust protection cap immediately.
To replace the dust protection cap 3, insert a slotted screw-
driver with a slot width of 2 – 3 mm into the recess at the bot-
tom housing shell behind the dust protection cap, and remove
the dust protection cap. Mount a new dust protection cap en-
suring that it is seated tightly.
Regrinding Steel Application Tools
Good working results can only be achieved with sharp appli-
cation tools. Therefore, resharpen application tools in good
time. This ensures a long service life of the application tools
and good working results.
Regrinding with a Belt
Sander:
Mount the belt sander into a
stationary device.
Turn around the electric
scraper with the steel appli-
cation tool installed by 180°.
Do not start the electric
scraper.
Observe the running direction of the sanding belt when
regrinding.
Regrinding with a Bench
Grinder:
Turn around the electric
scraper with the steel appli-
cation tool installed by 180°.
Do not start the electric
scraper.
Take care that the cutting
edges of the steel application tool are not subject to annealing
coloration (blue-coloring), as this will impair the hardness of
the application tools.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.

After-sales Service and Customer Assistance

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
Bosch Power Tools

Publicidad

Tabla de contenido
loading

Tabla de contenido