Zoeller APak Instrucciones De Instalación página 8

APAK LED, BUTTON, ALARM, AND Z CONTROL
®
LED and Alarm Power LED
Behaviors
Input 1 or Input 2 In Alarm
Low Battery Alarm
Power Out Alarm
Z Control
Silence Button Press/Release
Hold 3 Seconds
Hold 4 Seconds
Hold While Applying AC To
APak
Hold 12 Seconds
Communications Communication With
and Battery Life Z Control
Communication with
Z Control
Alarm Condition
Present
Auxiliary Output
Battery Life
*AP Mode is when the APak is broadcasting its "name", or SSID. The SSID is in the format ZCTL_APAK_xxxx where "xxxx" is the first 4 digits of
®
your APak 's Device ID. The APak'
®
connectivity to the APak . This is required in order to give your APak
®
AC and DC Mode
Power LED is on when AC and DC
power are present.
Input LED on solid.
Alarm triple beeps continuously.
Power LED blinks.
Alarm triple beeps every 5 seconds.
All LEDs go out to conserve battery
power.
Power LED blinks and alarm double
beeps every 30 seconds.
LED LED is solid when connected to
®
router and Z Control Cloud.
LED is off when APak
mode.*
LED blinks when Wi-Fi
process.
LED blinks faster if APak
attempting to reconnect to a known
router.
LED alternates blinking fast then
slow when APak is connected to
router but internet is lost.
Silences Alarms. LED that is in
alarm stays on (or blinks) until
APak is Reset.
®
Resets any active alarms and
returns APak to standby mode.
®
Initiates a LED and Alarm Test. Will
flash and double beep 3 times.
APak will enter AP mode*. For
®
APak to revert to previous Wi-Fi
® ®
settings, power cycle again.
Complete reset of APak
settings, including erasing Wi-Fi
settings . APak
® ®
mode.*
Communication is nearly
Cloud continuous.
®
Notification sent to user after 10
minutes of no communication.
Cloud Lost
®
Immediate communication to
Z Control Cloud.
®
Triggered for Input 1, Input 2, Pow-
er Out, and Low Battery Alarms.
1-2 years with normal use.
s SSID will show up in your phone/tablet/computer's list of available Wi-Fi
®
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624
© Copyright 2021 Zoeller
AC Only Mode
Power LED is on when AC power
is present.
Input LED on solid.
Alarm triple beeps continuously.
N/A
N/A
LED is solid when connected to
router and Z Control
is in AP LED is off when APak
®
mode.*
setup is in LED blinks when Wi-Fi
®
process.
is LED blinks faster if APak
®
attempting to reconnect to a known
router.
LED alternates blinking fast then
slow when APak
router but internet is lost.
Silences Alarms. LED that is in
alarm stays on (or blinks) until
APak is Reset.
®
Resets any active alarms and
returns APak
®
Initiates a LED and Alarm Test. Will
flash and double beep 3 times.
APak will enter AP mode*. For
®
APak to revert to previous Wi-Fi
®
settings, power cycle again.
to factory Complete reset of APak
®
settings, including erasing Wi-Fi
will enter AP settings. APak
mode.*
Communication is nearly
continuous.
Notification sent to user after 10
minutes of no communication.
Immediate communication to
Z Control Cloud.
®
Triggered for Input 1 and Input 2
Alarms.
N/A
the password credentials needed to connect to the Wi-Fi
®
Co. All rights reserved.
®
8
BEHAVIORS
®
DC Only Mode
Power LED off when only batteries
have been inserted, but will blink
when button pressed.
Input LED blinks and alarm double
beep every 5 seconds.
Power LED blinks and alarm beeps
every 10 seconds.
N/A
In order to conserve battery power,
Cloud. Z Control
® ®
is in AP connected to the router and Z
®
Control Cloud and off when the
®
setup is in Wi-Fi module is in low power
® ®
mode. AC power is required for
is Wi-Fi setup (see directions). To
® ®
test connectivity, trigger an Input.
is connected to
®
Silences alarm. LED still blinks ev-
ery 5 seconds until alarm is Reset.
In standby mode, a short beep will
occur to indicate APak
Resets any active alarms and
to standby mode. returns APak
Initiates a LED and Alarm Test. Will
flash and double beep 3 times.
APak will enter AP mode*. For
®
APak to revert to previous Wi-Fi
® ®
settings, power cycle again. See
"Battery Mode Only" note above.
to factory Complete reset of APak
®
settings, including erasing Wi-Fi
®
will enter AP settings.
®
Limited to once per day to conserve
battery power.
Notification sent to user after 24
hours of no communication.
Immediate communication to
Z Control
®
Does not function*
Approximately 1 year with normal
use.
, and selecting it will give you direct
®
These are the original installation instructions.
Visit our website:
zoellerpumps.com
LED is dimly lit while
is ready.
®
to standby mode.
®
®
to factory
®
®
Cloud.
of your choice.
®