Machine Features; Intended Use; Safety Instructions - Protool QuaDrive DRC 12-4 TEC Manual Original / Lista De Piezas De Repuesto

Table of contents
1 Symbols ............................................ 12
2 Machine features ................................ 13
3 Intended use ...................................... 13
4 Safety instructions .............................. 13
5 Commissioning ................................... 14
6 Machine settings ................................. 14
7 Tool holder, attachments ...................... 14
8 Operation .......................................... 15
9 Service and maintenance ..................... 16
10 Transport ........................................... 16
11 Accessories ........................................ 17
12 Disposal ............................................ 17
13 Warranty ........................................... 17
14 EU Declaration of Conformity ................ 17
2

Machine features

[1-1] Bit holder
[1-2] ON/OFF switch
[1-3] Right/left switch
[1-4] Gear switch
[1-5] Torque thumbwheel
[1-6] Clamp for attaching to the belt
[1-7] Lighting button
[1-8] LED light
[2-1] Buttons for releasing the battery
[3-1] LED
[3-2] Battery pack
Not all of the accessories illustrated or described
are included as standard delivery.
3

Intended use

Cordless drills are suitable for drilling into metal,
wood, plastics and similar materials as well as in-
serting and tightening screws.
The BC 3 charger is designed for charging the bat-
tery packs listed.
The user is responsible for any damages and in-
juries caused by use which does not conform to
the intended purpose; including any damages and
wear caused by permanent industrial operation.
4

Safety instructions

4.1 General safety instructions
WARNING! Read all safety warnings and
all instructions. Failure to follow the warn-
ings and instructions may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or bat-
tery-operated (cordless) power tool.
4.2 Machine-related safety
instructions
- Hold power tool by insulated gripping sur-
faces, when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory con-
tacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
- The charger and power tool are not intended for
use by persons (including children) with limited
physical, sensory or mental ability or without
suffi cient experience and/or knowledge, unless
they are supervised by a person responsible
for their safety or have been instructed on how
the charger or power tool is to be used. Chil-
dren should always be supervised to ensure that
they do not play with the charger or the power
tools.
- Take care when drilling into walls as there is a
danger of rupturing concealed gas/water pipes
or cutting through power cables.
- Do not open the battery pack or the charger.
Even after disconnection from the mains, there is
still a high capacitor voltage inside the charger.
- Make sure that metal objects (such as metal
chips) do not collect in the battery pack retain-
ing slots or enter the machine through the air
vent slits (danger of short circuit).
- Protect the battery pack from excessive heat or
constant heat sources such as sunlight or naked
fl ames. There is a risk of explosion.
- Never use water to extinguish burning LiIon bat-
tery packs, always use sand.
4.3 Emission levels
Levels determined in accordance with EN 60 745
are typically:
Sound pressure level
Noise level
Uncertainty
CAUTION
Operating noise
Damage to hearing
► Use ear protection!
Vibration emission value a
directions) and uncertainty K measured in accord-
ance with EN 60 745:
Screwing
Drilling in metal
Uncertainty
Declared total value of vibrations was measured
according to standard measure method and can
be used for comparison one powertools with the
others.
L = 73 dB (A)
PA
L = 84 dB (A)
WA
K = 3 dB
(vector sum for three
h
a < 2.5 m/s
h, S
a = 5.6 m/s
h, D
K = 1.5 m/s
2
2
2
13