Publicidad
Enlaces rápidos
Instructions / Instructions / Instrucciones
Istruzioni / Instructies /
™
Mark X
PC Board Repair Kit 287993
- Heavy Duty Electrical Airless Sprayer of Plasters and Paints -
- Pulvérisateur électrique sans air pour usage intensif et pour enduits et peintures -
- Pulverizador eléctrico, sin aire, para uso intensivo, para enyesados y pinturas -
- Spruzzatore elettrico airless per usi gravosi per intonaci e vernici -
- Heavy-duty elektrisch airless spuittoestel voor pleister- en schilderwerk -
Models / Modèles / Modelos / Modelli / Modellen: 249627, 249628
228 bar (22,8 MPa, 3300psi) Maximum Working Pressure / Pression maximale de service / Presión máxima de trabajo /
Pressione massima di esercizio / Maximum werkdruk
Important Safety Instructions
Read all warnings and instructions in 311421
manual. Save these instructions
Instructions de sécurité importantes
Lire toutes les mises en garde et instructions de
311421 manuel. Sauvegarder ces instructions.
Instrucciones importantes de seguridad
Lea todas las advertencias e instrucciones de 311421
manual. Guarde las instrucciones.
Importanti istruzioni sulla sicurezza
Leggere tutte le avvertenze e le istruzioni contenute
in 311421 manuale. Conservarle.
Belangrijke veiligheidsinstructies
Lees alle waarschuwingen en instructies in
311421 handleiding. Bewaar deze instructies.
311421
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001
311514 rev.A
Publicidad
Manuales relacionados para Graco Mark X 249627
Resumen de contenidos para Graco Mark X 249627
- Página 1 Leggere tutte le avvertenze e le istruzioni contenute in 311421 manuale. Conservarle. Belangrijke veiligheidsinstructies Lees alle waarschuwingen en instructies in 311421 handleiding. Bewaar deze instructies. 311421 Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001...
- Página 2 Pressure Control Replacement / Remplacement du système de contrôle de la pression / Cambio del control de presión / Sostituzione del controllo della / Vervangen van de drukregelaar ti7561a Pressure Control Removal Warning: Do Pressure Relief; Remove four screws and Disconnect display Remove bottom two screws page 27.
- Página 3 Pressure Control Removal Disconnect transducer Disconnect motor resolver Disconnect motor two wire Disconnect potentiometer connector from motor power connector from connector from motor connector from motor control board. motor control board. control board. control board. Dépose du système de contrôle de la pression Débrancher le connecteur Débrancher le connecteur Débrancher le connecteur...
- Página 4 ti7818a Pressure Control Removal Remove two bottom Remove blue (NEUTRAL) Remove 10/14A switch screws. Remove top two connector from motor connector from motor screws and partially control board. Remove control board. remove control housing. black (LINE) connector from filter board. Dépose du système de contrôle de la pression Déposer les deux vis du Débrancher le connecteur...
- Página 5 Pressure Control Removal Slide transducer grommet out Disconnect motor connector Disconnect two coil connectors Caution: Note screw locations now of control housing and remove from motor control board. from motor control board. for replacement later. Screws in the control housing. wrong positions can damage the motor control board.
- Página 6 Pressure Control Installation Apply an even layer of thermal Caution: Install motor control board: Install motor control board with compound 110009 to • To reduce risk of motor control board failure, do all nine screws loosely in place in numbered sequence. completely cover component not overtighten screws.
- Página 7 ti7585 Pressure Control Installation Connect two coil connectors Connect motor connector Slide transducer grommet to motor control board. to motor control board. into control housing. Pose du système de contrôle de la pression Brancher les deux Fixer le connecteur du Glisser le passe-fil dans connecteurs de la bobine moteur sur la carte de...
- Página 8 ti7818a Pressure Control Installation Install 10/14A switch Install blue (NEUTRAL) Install control housing with Connect potentiometer connector to motor control connector to motor control two top screws and two connector to motor control board. board and black (LINE) bottom screws. board.
- Página 9 Pressure Control Installation Connect motor two-wire Connect motor resolver Connect transducer Install control panel with connector to motor control connector to motor control connector to motor control two screws. board. board. board. Pose du système de contrôle de la pression Raccorder le connecteur à...
- Página 10 TO PLACE AN ORDER, contact your Graco distributor, or call 1-800-690-2894 to identify the nearest distributor. All written and visual data contained in this document reflects the latest product information available at the time of publication.