Chapin 31420 Manual De Instrucciones

WARNING!
Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store
or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full
foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent eject-
ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any
means other than the original pump. Do not attempt to modify or repair this product except with
original manufacturer's parts. Never spray flammable materials or heat, pressure, or gas produc-
ing chemicals. Always read and follow manufacturer's instructions before use with this sprayer
as some chemicals may be hazardous when used with this sprayer.
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known
to the State of California to cause birth defects and other reproductive harm. Wash hands after
handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
Felicitaciones!
¡
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
6-6136 6-5943 6-4626
Hose Nozzle Shut-off Handle
Manguera Tobera Mango de cierre
Tuyau Buse Poignée du robinet
6-7756 Extension wand, Vara de extensión, Rallonge 6-7749 Extension wand, Vara de extensión, Rallonge
(31010, 31020, 31030, 36140) (30220)
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus) 6-1925
Printed in USA
1. Hose to Tank
1A
Hose Barb
2. Nozzle
2A
Sk-1113-1
Attach nozzle to shut-off handle or extension wand.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank
outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these
conditions are found, replace hose before using. Replace with original manufacturer's
parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect
interior and exterior of tank for signs of deterioration of body and bottom. Any sign
of deterioration indicates possible tank weakening and could result in explosive
bursting under pressure. If any of these signs are found, discard tank immediately and
replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 10-20 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions),
empty tank, and proceed with Filling, Pressurizing and Spraying Instructions.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on
chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to
6-3337
accommodate pump.
Strap, Correa, Sangle
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump
( 31020, 31030, 36140, 30220)
in tank and tighten securely.
5. Pressurizing and Spraying
5A
Turn handle clockwise
to tighten. Push handle
down, turn 1/4 turn
counterclockwise to
release.
011269 (A) R0000
Make sure hose is pushed all the way to
the tank. Make sure hose clamp is tight
and below the hose barb. Turn clockwise
with a screwdriver to tighten.
2B
5C
5B
5D
Pump until you feel Push handle, down, Adjust spray pattern
resistance. turn 1/4 turn clockwise by turning nozzle cap.
to lock. Begin spray- Do not turn cap more
ing. than 2 turns or cap may
Re-pump sprayer as come off allowing spray
required to maintain material to spray back
spray force. on you.
6. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until
air begins to escape. Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
7. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling,
Pressurizing and Spraying Instructions, except pump unit only 10-15 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and
empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through
opening in cover.
8. Fatigue-Free Spraying
For constant spraying, push down on shut-off handle
and move grey locking mechanism away from you.
To release, squeeze handle and move the grey locking
mechanism back towards you. ( Not all models are
provided with this feature).
9. Troubleshooting
Tank pressurizes but does not spray.
-
WARNING:
Release pressure in tank before troubleshooting.
Clean shut-off (Fig. 9A- 9D)
9A 9B
Handle
Pull handle Insert notches from un-
straight up. derside of handle into
plunger grooves and
turn counterclockwise.
Tighten plunger clockwise until flush
9D
to top of shut-off body. Do not over-
Plunger flush
with body
tighten or unit may not spray. Slide
forks under plunger, push handle
down until it snaps into place.
Clean Nozzle Assembly (Fig. 9E) Remove nozzle cap. Clean and re-assemble.
-
9E
Nozzle Cap
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
8A
Locking
mechanism
9C
Plunger
Diaphragm
Body
Remove plunger and diaphragm.
Clean plunger, diaphragm and body. Flip
diaphragm and replace.