SOLAC LV1700 Instrucciones De Uso página 11

InStRuctIOn uSIng FOR AcceSSORIeS
1. extension tuve (Fig.4)
Assemble the extension tube if the steam clea-
ner is to be used to clean floor or high place win-
dows or difficult to reach areas. To do this, push
the open end of the tube into the steam gun until
the release button of the steam gun clicks into
place. And one or two extension tube if required.
Press in the appropriate the release button and
pull the tubes apart with a download movement
to take the extension tube off.
2. big nozzle (Fig.5)
This nozzle makes it possible to clean hard to
reach places such as corners, joints and toilets
with ease. Simple push the bent nozzle firmly
into the gun directly.
3. round brush (Fig.6)
The metal and nylon round brush are pushed
Firmly into the big nozzle until there is a sound.
Even the most stubborn dirt can be removed.
e.g. blinds, central heating radiators etc.
Please use small mental brush. Thenylon brush
is suitable for heavystaining on less sensitive
materials such as stainless steel. Simply pulling
it off with a downward movement can remove it
directly.
4. Ironing brush (Fig.7)
To iron the cloth, sofa etc, put the white ironing
towel on the ironing brush and connect with
steam gun. Besides, you can fixed the extension
tube in the hole by open the back cover to put
the clothes hanger on the extension tube. And
you can put the clothes directly.
5. Window brush (Fig.8)
To clean window, mirrors, or tiles those which
with smooth surface objects, please use the win-
dow brush which is with rubber blade combined
withbrush sprayer to clean. When installed,knot
on two prominent part ofthe hook on to the glass
scraper, then put the whole cover of glass brush
to ironing, issued a "clicking" sound, then insta-
llation is complete.
When ironing the cloth,you can put the exten-
sion tube in the hole of the unit, than put on the
hanger on it.
If temperature is lower than 0º, please do
not use this product to clean glass
6. Floor brush (Fig.9)
Floor brush nozzle to the end of extension tube.
LV1700_limpiavapor_2.indd 11
Ensure that nozzle clicks into place on assem-
bly. The floor brush is ideal for cleaning washa-
ble wall and floor coverings. It may be used with
or without the towel. Pressure on the inner side
of the holder, open the clips to hold the towel.
Add the carpet glider if you need to clean the
carpet.
Or add the brush if you need to clean the geos-
trophy etc.
FILLIng wIth wAteR:
You must fill the water compartment before tur-
•
ning on the appliance.
Do not force open the safety cap; make sure
•
the appliance is completely depressurized
prior to opening.
Remove the steam pressure pressing steam
•
release button (5)
Slowly unscrew the safety cap (7) by pressing
•
down and turning in the anti-clockwise direc-
tion to enable the remaining steam that might
be in the boiler
Fill the compartment with cold water.
•
Pour in water using the measuring cup and
•
funnel supplied. The steamer's maximum ca-
pacity is 1,5 litres.
Screw on the safety cap (7) by pressing down
•
and turning in the clockwise direction to the
end.
Check that the safety cap is screwed on tightly
•
before switching on the appliance.
uSe:
Unroll the cable completely before plugging it
•
in.
Take the length of cable required out of the
•
housing.
Connect the appliance to the mains.
•
Turn the appliance on, by using the on/off
•
switch.
The pilot light (5) comes on.
•
Leave to heat up for a few 6 Minutes.
•
Wait until the pilot light (5) has gone out which
•
will indicate that the appliance has reached an
adequate temperature.
During the appliance's use the pilot light (5) will
•
come on and off automatically, indicating the
heating elements are working, and therefore
maintaining the desired temperature.
SteAM FLOw cOntROL:
The appliance has a FIG 2 control knob that
•
allows to get the control of the steam flow.
en
29/7/16 8:41