Global Settings; Factory Reset - Hughes & Kettner GrandMeister Deluxe 40 Manual De Instrucciones

GrandMeister Deluxe 40 – Manual 1.1
MIDI Channel Clean
1 = ¢
2 =
¢
3 =
¢
4 =
¢
5 = ¢
6 = ¢
7 =
¢
8 =
¢
9 =
£
10 = £
11 =
£
12 =
£
13 =
£
14 =
£
15 = £
16 =
£
Press and hold the Store button for more than three seconds to save the
settings and quit MIDI setup mode. The amp is now back in normal
operating mode.
MIDI SETTINGS
You'll also find the diagrams shown in this chapter on your amp's bottom
panel.

8.2 Global Settings

If you press the Store and FX Access buttons simultaneously for more than
three seconds when the amp is in Standby mode (the Play/Standby switch
is set to Standby), the Store button will start flashing. The following LEDs
and buttons on the amp will then serve special programming purposes:
• FX Access: This indicates the status of Global Power Soak mode. The
button lights up when Global Power Soak mode is active. To deactivate
it, press the FX Access button again.
• Noise Gate: This indicates the status of Global EQ mode. The button
lights up when Global EQ mode is active. To deactivate it, press the
Noise Gate button again.
GLOBAL SETTINGS
8.3 MIDI implementation chart / controller list
In addition to controlling all switching functions via MIDI program changes,
you can also change the parameters of every single editable function of the
amp in real time via MIDI control changes. The following chart shows the
editable functions and the corresponding controller numbers:
12
Crunch Lead Ultra
¢ ¢ ¢
¢ ¢ {
¢ £ ¢
¢ £ £
£ ¢ ¢
£ ¢ £
£ £ ¢
£ £ £
¢ ¢ ¢
¢ ¢ £
¢ £ ¢
¢ £ £
£ ¢ ¢
£ ¢ £
£ £ ¢
£ £ £
Controller Function
number
1 Modulation Intensity
4 Delay Time, 128 steps, 51 ms to 1360 ms
7 Volume (soft)
9 Mute On-Off. On status remains active until the amp channel is changed,
the volume parameter is changed or the amp is re-started.
12 Mod-FX Type
20 Gain (soft)
21 Bass
22 Mid
23 Treble
24 Resonance
25 Presence
26 Modulation Speed (always for the active modulation effect)
27 Delay Feedback
28 Delay Volume
29 Reverb Volume
30 Power Soak Switching (5 sectors)
31 Channel Switching (4 sectors)
52 Mod-FX On-Off
53 Delay On-Off
54 Reverb On-Off
55 FX-Loop On-Off
56 Gain (hard)
57 Volume (hard)
63 Noise Gate On-Off
64 Boost On-Off
Heads up: You can adjust GrandMeister Deluxe 40's volume levels via
a controller pedal (MIDI controller #7), but only up the maximum value
stored in the amp. This means that a controller pedal connected to the
FSM-432 does not work like a global remote control for the amp's overall
volume level because its control range is always determined by the
maximum value stored in each preset.

8.4 Factory Reset

A factory reset is a seldom-needed feature. Nonetheless, please read these
instructions carefully to ensure you don't accidentally delete your presets.
You can perform a factory reset by doing the following:
Press "Store" and "FX Access" simultaneously while powering the amp
up by using the Power/On switch. Both buttons will flash to indicate the
successful factory reset.
FACTORY RESET
Caution: Please note that this procedure is a last-resort option. It will
reset all settings, including the 128 MIDI-switchable presets (chapter 2)
and the basic MIDI configuration (chapter 8.1).