Trouble Shooting; Repairs; Environmetal Protection - Metabo Mega 600 D Manual De Instrucciones Original

Self-storing Coil Air Hose, Rilsan
•
(not illustrated)
c/w quick coupler and male plug;
2.5 m working length; outer diameter
8 mm; inner diameter 6 mm.
Stock-no. 090 105 4940
Self-storing Coil Air Hose, Rilsan
•
(not illustrated)
c/w quick coupler and male plug;
7.5 m working length; outer diameter
8 mm; inner diameter 6 mm.
Stock-no. 090 105 4959
Self-storing Coil Air Hose, Rilsan
•
(not illustrated)
c/w quick coupler and male plug;
10.0 m working length; outer diame-
ter 10 mm; inner diameter 8 mm.
Stock-no. 090 105 4967
Hand-crank Hose Reel SA 100
•
(not illustrated)
c/w 20.0 m braided air hose; outer
diameter 15 mm; inner diameter
9 mm.
Stock-no. 090 105 4975
Automatic Retractable Hose Reel
•
SA 200 (not illustrated)
suitable for wall and ceiling mount-
ing; retracts automatically by simply
pulling on hose; with 8 m PU air
hose; outer diameter 13 mm; inner
diameter 8 mm.
Stock-no. 090 105 4550
Accessory kits
L Accessory Kit LPZ 7-S
comprising: Blow gun, tyre inflator
gauge, tyre valve nozzle, needle tip
nozzle, paint spray gun, spray gun,
self-storing coil air hose.
Stock-no. 090 100 3858
Accessory Kit LPZ 7-P
•
(not illustrated)
comprising: Blow gun, tyre inflator
gauge, tyre valve nozzle, needle tip
nozzle, paint spray gun, spray gun,
10 m braided air hose.
Stock-no. 090 100 3890
Accessory Kit LPZ 6 (not illustrated)
•
comprising: Blow gun, tyre inflator
gauge, tyre valve nozzle, needle tip
nozzle, paint spray gun, 5 m braided
air hose.
Stock-no. 090 104 4487
Accessory Kit LPZ 4 (not illustrated)
•
comprising: Blow gun, tyre inflator
gauge, paint spray gun, self-storing
coil air hose.
Stock-no. 090 101 3845
Accessory Kit LPZ 2 (not illustrated)
•
contains change handle with blow
gun, tyre inflator gauge, paint spray
gun, self-storing coil air hose.
Stock-no. 090 105 5971
7.

Trouble Shooting

A
Danger!
Prior to all servicing:
– Switch Off.
– Unplug.
– Wait until the compressor has
come to a complete stop.
– Ensure the compressor and all air
tools and accessories connected
to it are relieved from pressure.
After all servicing:
– Check to see that all safety devic-
es are operational.
– Make sure that no tools or other
parts remain on or in the machine.
Compressor does not run:
No mains voltage.
•
– Check cables, plug, outlet and
mains fuse.
Mains voltage too low.
•
– Use only extension cables with
sufficient lead cross section (see
"Technical Specifications"). Avoid
using extension cable with cold
machine.
Compressor was stopped by unplug-
•
ging.
– Switch compressor OFF at the
On/Off switch, then ON again.
Motor has overheated, caused by in-
•
sufficient cooling (cooling fins cov-
ered).
– Remove cause for overheating
and allow to cool down for ap-
prox. 10 minutes, then start again.
ENGLISH
Compressor runs but does not build
up sufficient pressure.
Drain cock on cup of filter/regulator
•
unit open.
– Close drain cock.
Check valve leaky.
•
– Have check valve serviced by
qualified service centre.
Air tool is not supplied with sufficient
pressure.
Pressure regulator not opened wide
•
enough.
– Open pressure regulator more.
Hose connection between compres-
•
sor and air tool leaky.
– Check air hoses, replace defec-
tive parts if necessary.
8.

Repairs

A
Danger!
Repairs to electric tools must be car-
ried out by qualified electricians only!
Electric tools in need of repair can be
send to the service centre in your coun-
try. See spare parts list for address.
Please attach a description of the fault
to the electric tool.
9.

Environmetal protection

The machine's packaging can be 100 %
recycled.
Worn out machines and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
These instructions are printed on chlo-
rine-free bleached paper.
17