Important Safety Instructions; General Safety; Product Specifications - Pentair PRO-SOURCE APSC Serie Manual Del Propietário

Safety • Product Specifications

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains
important instructions that should be followed during
installation, operation, and maintenance of the product.
Save this manual for future reference.
Install in compliance with all applicable laws, codes and
ordinances. Non-compliance may cause product failure,
property damage, and/or personal injury.
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential
for personal injury!
indicates a hazard which, if not avoided, will
result in death or serious injury.
indicates a hazard which, if not avoided,
could result in death or serious injury.
indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE addresses practices not related to
personal injury.
Carefully read and follow all safety instructions in this
manual and on product.
Keep safety labels in good condition. Replace missing or
damaged safety labels.
Install this tank in vertical position only. If your
installation requires a horizontal tank, contact your
dealer for available steel tanks.
Rules For Safe Installation And Operation
Risk of explosion. Installation must comply
with all applicable state, provincial, and local statutes,
codes and ordinances. Non-compliant installation
may result in product failure, property damage, and/or
personal injury.

Product Specifications

Tank Capacity
Model
Litres (U.S. Gallons)
APSC-14-4-01 53 (14)
APSC-20-6-01 76 (20)
APSC-30-9-01 114 (30)
APSC-40-12-01 151 (40)
APSC-48-14-01 182 (48)
APSC-60-20-01 227 (60)
APSC-80-23-01 303 (80)
APSC-85-25-01 322 (85)
APSC-119-35-01 450 (119)
Maximum Internal Water Temperature: 49° C (120° F).
Maximum Ambient Air Temperature: 49° C (120° F).
Allow 305 mm (12") clearance over top of tanks for service access.
1. Read the owner's manual and Rules for Safe
2. Always test water from well for purity before
3. Before installing or servicing your tank, BE SURE
4. Release all pressure before working on tank or
5. BE SURE your pump electrical circuit is
6. Remove bleeder orifices, air volume controls or other
serious or fatal in jury and/or damage to equipment,
system pressure must be less than 873 kilo pascals
(kPa) (125 pounds per square inch gauge (psig)) under
any circumstances. Failure to follow this instruction can
result in tank explosion. If system discharge pressure can
exceed 873 kPa (125 psig), install a relief valve capable
of passing the full pump volume at 873 kPa (125 psig).
Install relief valve in pump supply line to tank, as close
to tank as possible.
before attempting to install, operate, or service this tank.
To avoid possible equipment failure, severe injury, and
property damage, do not allow pump, tank, or piping
system to freeze.

General Safety

All tanks are factory pre-charged with air. When
installing tank, adjust pre-charge to 14 kPa (2 psig) below
pump cut-in pressure setting. To do this, bleed air from or
add air to the valve on top of the tank.
Tank Diameter Tank Height
Millimetres (Inches) Millimetres (Inches)
716 (28,2)
866 (34,1)
406 (16)
1176 (46,3)
1499 (59,0)
533 (21) 1664 (65,5)
610 (24) 1107 (43,6)
533 (21) 1128 (44,4)
1453 (57,2)
610 (24)
1915 (75,4)
Installation and Operation instructions carefully.
Failure to follow these rules and instructions could
cause serious bodily injury and/or property damage.
using. Check your local health department for
testing procedure.
pump electric power source is disconnected.
system. Make sure all air pressure has been released
before removing tank flanges.
properly grounded.
air charging devices in existing system.
Risk of explosion. To prevent possible
Hazardous pressure. Read Owner's manual
Discharge Tapping
(BSP)
1"
1-1/4"
2
Distance from Base to
Center Line of Fitting
Millimetres (Inches)
44,5 (1,75)
57,2 (2,25)