Fein FSC1.6X Manual Del Usuario página 18

en
18
Character Unit of measure,
international
P W
1
P W
2
n 1/min
S
°
L dB
wA
L dB
pA
L dB
pCpeak
K...
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
/min, m/s
For your safety.
Read all safety warnings and all instruc-
WARNING
tions. Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
hand-guided power tool for commercial use in weather-
protected environments using the application tools and
accessories recommended by FEIN.
FSC1.6X/FSC1.6Q:
– for cutting polyurethane beads for glazier work in
automobiles, lorries and busses,
– for sawing out chassis sections and removing under-
seal materials,
– for sanding of chassis parts.
FSC2.0Q:
– for sawing wood (max. 78 mm), plastic, glass-fibre
reinforced plastics (GFRP) and for sawing sheet metal
(max. 1 mm),
– removing tile joints and rasping or scraping off tile
grout or carpet remainders,
– cutting elastic sealants (silicone or acrylic) on facades/
frontages and roughing groove faces,
– sanding or rasping of smaller surfaces.
Unit of measure,
national
W
W
1/min
°
dB
dB
dB
2
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2
rpm, m/s
Explanation
Power input
Output
Rated oscillation rate
Oscillation angle
Sound power level
Sound pressure level
Peak sound pressure level
Uncertainty
2
Acceleration
Basic and derived units of measure from the
international system of units SI.
2
Special safety instructions.
Hold the power tool by the insulated gripping surfaces when
performing operations where the application tool could
contact hidden wiring or its own power cord. Application
tools that come into contact with a "live" wire can make
exposed metal parts of the power tool "live" and shock
the operator.
Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the work by
hand or against your body leaves it unstable and may lead
to loss of control.
Do not work materials where substances can be released
that are harmful to one's health, e. g., asbestos. Hazard-
ous/toxic dusts develop when sanding, e.g., lead-contain-
ing coatings, some wood types or metal.
Grasp the power tool in such a safe manner that your body
never comes into contact with the application tool, espe-
cially while working with application tools such as saw
blades or other blades pointed toward the grasping range.
Touching sharp tips or cutting edges can lead to injuries.
Wear personal protective equipment. Depending on the
application, use a face shield or safety goggles. Wear a
dust mask. Wear hearing protection. The eye protection
must be capable of protecting against flying particles gen-
erated by the various different operations. The dust mask
or respirator must be capable of filtering particles gener-
ated by your operation. Prolonged exposure to high
intensity noise may cause loss of hearing.
Wear protective gloves. Danger of injury due to sharp-
edged accessories.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection against
an electric shock will be ineffective. Adhesive labels are
recommended.
Clean the ventilation slots of the machine regularly. The
motor fan draws dust into the housing. Excessive accumu-
lation of metal dust can cause electrical dangers.
Before putting into operation, check the mains connection
and the mains plug for damage.