Bounce Flash; Wireless Flash - Sigma EF-530 DG SUPER EO-ETTL II Instrucciones

MULTI FLASH MODE
While the shutter is open, the flash will fire repeatedly. By doing so a series of images of the subject will be
exposed in one frame. A
possible to set the firing frequency between 1Hz and 199Hz. Up to 100 flashes can be fired continuously.
The maximum number of flashes varies, depending on the
settings. (Please refer to
◆ This function cannot be used with EOS 700, 750, 850 cameras.
1. Set the camera's exposure mode to M
2. Press the MODE button until the Multi-flash mode
3. Press the SEL button until the flash firing frequency starts to blink.
4. Press the + or - button to set the desired flash frequency value.
5. After pressing the SEL button again, the flash power level will blink.
6. Press the + or - button to set the desired power level.
7. Press the SEL button again, the number of flashes will blink.
8. Press the + or - button to set the desired number of flashes.
9. Press the SEL button again, the display will stop blinking.
10. When the ready light of the flash is illuminated, the unit is ready to use.
Note: Please set the shutter speed longer

BOUNCE FLASH

When you take a photo with flash in a room, sometimes a strong shadow will appear behind the subject, if
you point the flash head upwards or sideways to reflect the light off the ceiling, wall etc. the subject will be
illuminated softly. Press the lock button and adjust the flash head to set the bounce angle.
UP: 0°, 60°, 75°, 90°
RIGHT: 0°, 60°, 75°, 90° LEFT: 0°, 60°, 75°,90°, 120°, 150°, 180°
When the bounce flash mode is activated, a bounce indicator
appear on the LCD panel.
Choose a white surface for bouncing the flash, otherwise the image's
colour may be incorrect.
Depending on the reflecting surface, the subject distance and other
factors, the effective distance range for the TTL AUTO may change.
Please check for correct exposure confirmation (ETTL or TTL mark on
the LCD panel) after releasing the shutter.
Close-up Exposures
Bounce flash can be tilted 7° downward for close-ups. The Flash will be effective only for the subjects 0.5
meter to 2 meters. When the flash head is tilted

WIRELESS FLASH

When using the "Wireless Flash" mode, you can take pictures with a more three-dimensional
make natural images by
extension cord connecting
between the camera body and the flash will be
Flash" mode, the camera will calculate the correct exposure automatically.
◆ The type A camera
functions only. The EOS750 and EOS850 cannot be used with "Wireless Flash".
◆ In this instruction we
call a flash unit at a remote position
◆ When setting a slave unit at the desired position, you can use
has a screw hole for a tripod.
◆ Place the slave flash unit at the desired location. Do not place the slave unit within the picture area.
Set the flash unit within the range of 0.5m/1.5ft~5m/16ft from the subject and set the camera body within
◆
the range of 1m/3ft~5m/16ft from the subject.
bright subject with a dark background
table 3 on the last page).
mode and
DOWN: 0°,7°
using shadowing depending on the flash
the camera body and flash. In case of
models can be used with "Wireless Manual Flash" and "Wireless Multi Flash"
call the flash unit which
a "Slave unit".
shows more effectively in this mode. It is
flash's power output
set the F number.
appears.
than; Number of Flashes you want ÷ Firing Frequency
will
7°, will blink.
the
achieved by the light
is attached to the camera body
the
and firing frequency
position. This can be done without
EF-530 DG SUPER, communication
produced by the flash. In the "Wireless
the "Master unit " and we
mini-stand provided. This mini-stand
feeling, or
any
20