Fein GIL5V6 Instrucciones De Uso página 11

Changing the grinding belt.
Before any work on the machine itself, pull the power
plug of the belt grinder from the socket outlet.
Lower the contact wheel (16) with the star-knob
bolt (28).
Replace the grinding belt (see GI150 Operating
Instructions).
Adjust the tracking of the belt as already described.
Adjust the contact wheel and the brake wheel.
Shut the protective covers.
Extraction device.
The machine can be connected via the connection sleeve
to an undercarriage or base unit with dust extraction.
Repair and customer service.
Repairs may be carried out only by qualified per-
sons in conformity with the valid regulations.
For repairs, we recommend our FEIN customer service
centre, the FEIN authorised service centres and FEIN
agencies.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
To prolong gear life, change gear sealing ring
(3 90 00 004 52 3) after 18 months of use! Contact Fein
service.
Carry out the following maintenance regularly:
Blow out the ventilation slots at the motor housing
and the marked locations with compressed air.
Lubricate the machine daily (when in use) with
machine oil at the locations marked.
Check the brake wheel and the contact wheel for
wear and damage each time when changing the
grinding belt. Have damaged parts replaced.
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's guarantee. For further
details on this, please contact your specialist dealer, your
national FEIN representative, or the FEIN customer serv-
ice centre.
Specifications.
Type
Reference number
No-load speed [rpm]
Power input [W]
Voltage [V]
Frequency [Hz]
Weight according to
EPTA-Procedure 01/2003 [kg]
Class of protection
Connection diagrams.
Type GIL Appendix 70
GIL
7 90 24 800 40 3 7 90 24 809 57 3
1730 / 1440
180
3 x 230 / 220
3 x 400 / 440
50 / 60
64
I/
Declaration of conformity.
GRIT declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Original language English/German
Environmental protection, disposal.
Stationary machines should be sorted for environment-
friendly recycling in accordance with national laws.
Noise emission values.
A-weighted emission pres-
sure power level measured
at the workplace L
pA
(re 20 μPa), in decibels
Measuring uncertainty K
in decibels
Measured A-weighted sound
power level L (re 1 pW),
wA
in decibels
Measuring uncertainty K
in decibels
Operating conditions
GIL mounted on GI150
Speed [rpm]
Material
Dimension
Grinding belt
REMARK: The sum of the measured emission value and
respective measuring inaccuracy represents the upper
limit of the values that can occur during measuring.
Wear ear protection!
Measured values determined in accordance with the cor-
responding product standard (see last page in this
Instruction Manual).
GIL5V6
7 90 24 806 44 3
1730 / 1440 1730 / 1440
180
3 x 575 3 x 230 / 220
3 x 400 / 440
60
64
I/
en
Idle Grinding
80.5
,
wA
4
90
,
pA
2.5
3000
–
–
– FEIN 36R
GILAUS
7 90 24 812 44 3
1730 / 1440
180
3 x 230 / 220
3 x 400 / 440
50 / 60
64
I/
11
94
4
100.5
2.5
3000
ST 37
8 x 40
Grit by
GILUSA
180
50 / 60
64
I/