Tabla de contenido
Publicidad
❍Foot control (Controller number 4)
Status
2nd byte
BnH
04H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
* This is transmitted only on the channel which is assigned to the drum kit part.
* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC is set to
"FOOT".
❍Data Entry (Controller number 6)
Status
2nd byte
BnH
06H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
mm = The value of the parameter specified by RPN.
* Only the channel assigned to the backing part are sent.
* When a pattern or a song are selected or adjust [PATTERN]-[PART]-[SETUP]-[PAGE 2]
BEND RANGE setting, the pitch bend sensitivity of the sequencer pattern data will be
transmitted.
Values for the RPN parameter, on the normal mode of TD-8, are as follows.
RPN
Data entry
MSB LSB
MSB LSB
00H 00H
mmH ---
7FH 7FH
--- ---
❍Volume (Controller number 7)
Status
2nd byte
BnH
07H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Volume:
00H - 7FH (0 - 127)
* Only the channel assigned to the percussion part and the backing part are sent.
* When a pattern or a song are selected, the part level of the sequencer pattern data will be
transmitted.
❍Pan (Controller number 10)
Status
2nd byte
BnH
0AH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = pan:
00H - 40H - 7FH (Left - Center - Right)
* Only the channel assigned to the backing part are sent.
* When a pattern or a song are selected, the pan of the sequencer pattern data will be
transmitted.
❍General purpose controller 1 (Controller number 16)
Status
2nd byte
BnH
10H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
* This is transmitted only on the channel which is assigned to the drum kit part.
* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or
ZONE CC are set to "GEN1".
❍General purpose controller 2 (Controller number 17)
Status
2nd byte
BnH
11H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
* This is transmitted only on the channel which is assigned to the drum kit part.
* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or
ZONE CC are set to "GEN2".
3rd byte
vvH
3rd byte
mmH
Explanation
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
RPN null
set condition where RPN is unspecified.
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
❍Hold 1 (Controller number 64)
Status
2nd byte
BnH
40H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127) 0-63 = OFF 64-127 = ON
* Only the channel assigned to the backing part are sent.
* Transmitted only when the TD-8 is in play for Pattern in which Hold 1 is recorded.
❍Effect 1 (Reverb Send Level) (Controller number 91)
Status
2nd byte
BnH
5BH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Reverb send level:
00H - 7FHÅi0 - 127Åj
* Only the channel assigned to the percussion part and backing part are sent.
* When a pattern or a song are selected, the reverb send level of the sequencer pattern data
will be transmitted.
❍RPN MSB/LSB (Controller number 101,100)
Status
2nd byte
BnH
65H
BnH
64H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
mm = upper byte of parameter number specified by RPN (MSB)
ll = lower byte of parameter number specified by RPN (LSB)
* Only the channel assigned to the backing part are sent.
* When a pattern or a song are selected, the pitch bend sensitivity of the sequencer pattern
data will be transmitted.
* Regarding the RPN please refer to p. 200.
Values for the RPN parameter, on the normal mode of TD-8, are as follows. Regarding the
value of each parameter, refer to Data Entry (Controller number 6).
RPN
MSB LSB
Parameter
00H 00H
Pitch Bend Sensitivity
7FH 7FH
RPN null
G Program Change
Status
2nd byte
CnH
ppH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
pp = Program number:
00H - 7FH (prog.1 - prog.128)
* Not transmitted when [SETUP]-[MIDI]-[PROG] PROGRAM CHANGE RX SW is set to
"OFF".(Initial Value is ON)
* Program changes corresponding to drum kit are sent when drum kits are selected.
* Program changes corresponding to each part's instrument are sent when songs or
patterns are selected. Also, when instruments are selected for parts, program changes for
the respective instruments are sent.
G Pitch Bend Change
Status
2nd byte
EnH
llH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
mm, ll = Pitch Bend value:
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* Transmitted only when the TD-8 is in play for pattern in which pitch bend change is
recorded.
I System Realtime Message
G Timing Clock
Status
F8H
G Start
Status
FAH
Aplicación MIDI
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
3rd byte
mmH
203
Publicidad
Tabla de contenido
