DeWalt DW756 Manual De Instrucciones página 8

Ocultar thumbs Ver también para DW756:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D
WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.

WARNING: To reduce the risk of injury, always
use proper guards when grinding and wear
eye protection.

CAUTION: Strands of wire cup brushes may break
and fly off while in use. Users and others in the area
should wear adequate eye, face and body protection.
Use only wire cup brushes that are rated at or greater
than the RPM shown on the tool's nameplate.

CAUTION: The use of any non-recommended
accessory may be hazardous.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Grinding wheels must fit within the confines of the guard
and must be rated higher than the recommended speed as
marked on the bench grinder nameplate.
Changing Accessories (Fig. F, G, I, J, K)
Change accessories when the spark guard can no longer be
adjusted to 1/16" (1.6 mm) from the wheel.
DW756 - use only wheels that measure 6" (152 mm) in
diameter. This tool has 1/2" (13 mm) arbors on each side.
DW758 - use only wheels that measure 8" (200 mm) in
diameter. This tool has 5/8" (16 mm) arbors on each side.
6
Follow the steps below to remove and replace an accessory.
1. Raise the eye shield
2. Loosen, but do not remove, the tool rest bolts
WALT
e
and pull the tool rest
remove it.
3. Loosen, but do not remove, the spark guard bolts
and pull the spark guard
remove it.
4. Remove the screws
remove the covers.
5. Using hex wrenches, grasp the two hex nuts
holding the wheels to the arbor shaft
of the tool (Refer to Fig. J, K). To remove the wheel
from the left side, turn the hex nut
holding the other stationary. To remove the wheel from
the right side, turn the hex nut
while holding the other stationary.
6. Remove the wheel flanges
7. Inspect the wheel for cracks, chips or any other visible
WALT Industrial
e
damage (other than normal wear) and discard if such
damage is found. Inspect the blotter
If the blotter is missing or severely damaged, replace
it with a piece of thin cardboard or blotter paper
cut to the same size. NEVER USE A WHEEL WITHOUT
A BLOTTER.
Fig. I
1
20
21
20
4
 2 
.
 4 
out as far as possible. Do not
out as far as possible. Do not
 1 
 20 
from both side covers
 22 
 24 
and the wheel
2
8
15
 21 
and
 22 
 23 
at each end
clockwise while
 22 
counter clockwise
 25 
.
for damage.
 26 

Publicidad

Tabla de contenido
loading

Tabla de contenido