Moser 1591Q Traducción Del Manual De Uso Original página 13

Product description
Description of parts (Fig. 1)
A Blade set
B On/off switch
C Charging indicator
D Charging stand
E Charging stand socket
F Oil for blade set
G Cleaning brush
H Attachment comb
I
Plug-in transformer
J Appliance plug
Technical data
Hand-held appliance
Drive:
Battery:
Battery operating time:
Dimensions (LxWxH):
Weight:
Emission sound pressure level: max. 60 dB(A) @ 25 cm
Vibration:
Charging stand
Dimensions
with accessories (LxWxH):
Weight:
Plug-in transformer
Type
Power consumption:
Operating voltage:
The appliance is safety insulated and radio screened. It meets
the requirements of EU Electromagnetic Compatibility Directive
2004/108/EC and Machinery Directive 2006/42/EC.
Operation
Preparation
Keep the packaging material for safe storage or
transport later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the appliance with the voltage stated
on the nameplate.
DC motor
NiMH battery
up to 100 min.
141 x 32 x 29 mm
approx. 132 g
< 2.5 m/s
2
72 x 96 x 58 mm
approx. 61 g
Adapter 6000
max. 12 W
100 – 240 V / 50/60 Hz
Charging the battery
Before the appliance is used for the first time, it
should be charged for approx. 2 hours!
1. Connect the appliance plug (J) on the plug-in transformer to
the charging stand socket (E) (Fig. 2ⓐ).
Battery overcharging is prevented thanks to intelligent
charge management.
2. Connect the plug-in transformer to the mains socket
(Fig. 2ⓑ).
3. Switch off the appliance using the on/off switch (Fig. 3ⓑ).
4. Place the appliance on the charging station (Fig. 2)
· During charging, the charging indicator (C) flashes
at evenly spaced intervals. When the battery is
fully charged, the charging indicator flashes at a
different rate (10 on / 1 off).
· After the appliance has been removed from the
charging stand, the display goes out (power sav-
ing mode).
· It will take no more than 120 minutes for the
appliance to charge to full capacity.
Battery operation
1. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3ⓐ/ⓑ).
· With the battery fully charged, the appliance can
be operated for up to 100 minutes. This capacity
is attained after approx. 5 - 10 charging cycles.
· In case of insufficient maintenance of the
blade set, the operating time can be reduced
considerably.
Operation
Cutting with the attachment comb
The appliance can also be operated with an attachment comb.
f The attachment comb has 5 detent positions for adjusting
the cutting length.
f The further the attachment comb is pushed in (retracted),
the shorter the cutting length.
The cutting length can be adjusted from 3 mm
(Fig. 5ⓐ) to 6 mm (Fig. 5ⓑ).
Attaching/removing the attachment comb
1. Slide the attachment comb on to the blade set in the direc-
tion of the arrow until it reaches the limit stop (Fig. 4ⓐ).
2. The attachment comb can be removed by pushing it in the
direction of the arrow (Fig. 4ⓑ).
ENGLISH
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
ar
13