GRAPHITE 59G887 Manual De Instrucciones página 11

TRANSLATION OF ORIGINAL MANUAL
RAIL TILE SAW
59G887
CAUTION: BEFORE USING THE DEVICE READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
Detailed safety conditions regarding use of saws for ceramic tile
cutting
• Power supply voltage must match the value indicated on the
rating plate of the tile saw.
• Connect the tile saw only to electrical system equipped with
residual current circuit breaker that will cut the power off in less
than 30 ms when earth leakage current exceeds 30 mA.
• When working outdoors use only extension cords designed for
outdoor use.
• When operating the saw strictly follow applicable regulations
regarding occupational health and safety.
• Make sure direction of cutting disc rotation matches the indicated
direction of the saw motor.
• Cutting disc of the saw should be free to rotate after installation.
• Always use anti-splinter goggles, hearing protection and anti-dust
mask.
• Always wear proper clothing for your work! Loose items of
clothing or jewellery might get caught by rotating cutting disc.
• Before any adjustment, measurement, cleaning or removing
jammed ceramic pieces always disconnect power supply from the
tool with the switch and remove the plug from mains socket!
• After repair or maintenance is carried out, install all guards and
protective parts before switching on the saw.
• Do not start working with the tile saw when tired or under
influence of medicines.
• It is vital that all persons who operate the tile saw are properly
trained for operation, using and adjustments of the tile saw.
• Replace damaged protective parts immediately.
• Never overload the saw, causing disc rotational speed to drop
down considerably.
• Keep the workplace clean. Before working remove waste material
and unnecessary objects.
• Keep bystanders away from the saw workplace.
• Keep the workplace well illuminated.
• Do not distract person who is working with the saw.
• After the motor is switched off with the switch, never attempt to
stop the cutting disc by applying side pressure.
• Immediately replace damaged cutting disc.
• Never use cutting discs with parameters different from specified in
this manual.
• Never attempt to remove or disconnect protection parts of the
saw.
• When you need a break, finish current cutting and then switch off
the saw.
• When a break in work and leaving the workplace is necessary,
switch off the saw with the switch and disconnect it from power
supply by removing the plug from mains socket.
• Check technical condition of the tile saw before starting to
operate:
all protection parts must be in good working order and operate as
supposed to,
screws and other mount parts must not be loosened,
all adjustment keys must be removed from the tool.
• Always ensure the processed material rests on the work table of
the saw with its whole surface.
• Never cut several pieces of material at a time.
• Do not unplug the tile saw from mains socket by pulling the cord.
Protect the power cord against excessive heat, oil and sharp edges.
• When operating the saw keep your body in firm, standing
position.
• All parts of the saw must be properly fixed.
• Repairs of the tile saw should only be carried out by qualified
person in authorized service workshop and with use of original
spare parts.
• Do not make profile cuts with the tile saw.
• When carrying the tile saw, hold only by transport handles, do not
hold by saw shields.
WARNING! When using electric tools always follow the basic
safety rules to reduce risk of fire, electric shock and body
injuries. Read all instructions before starting to operate the
product and keep them for future reference.
CAUTION: This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always
a small risk of injuries.
Explanation of used symbols
1. Read instruction manual, observe warnings and safety conditions
therein!
2. Warning, risk of cutting
3. Use hearing protection
4. Use safety glasses
5. Use protective gloves
6. For use indoors
7. Keep the tools away from children
8. Unplug from mains power before starting maintenance or repair
DESIGN AND INTENDED USE
Rail tile saw is designed for wet cutting of ceramic tiles and similar
materials, appropriate in size for the size of the rail tile saw. The rail
tile saw must not be used for cutting wood or metal. When working
with the rail tile saw, use only cutting discs designed for this type of
device. Rail tile saw is designed for all works from the range of
individual, amateur activities (tinkering).
Use the tool only in accordance with its purpose.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Locking knob for cutting length limiter
2. Rail
3. Head handle
4. Head
5. Water pump
6. Leg fixing screw
7. Switch
8. Working top
9. Base
10. Mitre gauge
9