GRAPHITE 59G887 Manual De Instrucciones página 12

11. Fence
12. Additional working top
13. Transport wheels
14. Leg
15. Bevel locking knob
16. Head locking screw
17. Support for transport wheels
18. Axis of transport wheels
19. Drain plug
20. Locking knob of mitre gauge
21. Installation knob of the mitre gauge
22. Adjustment knobs
23. RESET button
24. Power indicator
25. TEST button
26. Bevel angle scale
27. Cutting disc guard
28. Cutting disc
29. Knob for head vertical shift
* Differences may appear between the product and the drawing.
MEANING OF SYMBOLS
WARNING
EQUIPMENT AND ACCESSORIES
1. Base
2. Head with working top
3. Mitre gauge
4. Cutting length locking unit + knob
5. Leg installation bolt with washers
6. Handle installation bolt
7. Support for transport wheels
8. Axis of transport wheels
9. Transport wheel
10. Additional top
11. Drain plug
12. Ring spanner
PREPARATION FOR OPERATION
The rail tile saw is supplied disassembled. Take items out of the
package and assemble in the below described order.
RAIL TILE SAW ASSEMBLY
• Unfold the legs (14) from the base (9) (fig. A) and secure with the
screws (included) (fig. B).
• Attach the supports (17), wheel axis (18) and the transport wheels
(13) to the legs (14) (fig. C, D).
• Use the screws in the legs base to level the device.
• Install the drain plug (19) in the base hole (9) (fig. E)
• Attach the head with working top on the base (9). Make sure that
the water pump (5) is positioned correctly in the base (fig. F) (slide
the water hose onto the water pump stub pipe if necessary).
• Install the locking knobs for the cutting length limiter (1) in the rail
groove (2) (fig. G).
• Install the head handle (3) with the supplied screws as shown on
fig. H.
• Unscrew the head locking screw (16) (fig. I).
• Adjust force of pressure and cutting depth with the knob for head
vertical shift (29) (fig. H).
• Use the screw (21) to join the mitre gauge (10) to the fence (11)
(you can install the mitre gauge on both sides of the work table)
(fig. J).
The saw is equipped with additional working top (12), which allows
to extend the working top (8) when necessary (long tiles). The
additional working top (12) can be installed in 3 different positions,
its holes must be fitted onto pins in the base (9). It can be installed on
either side of the base. The adjustment knobs (22) in the bottom part
of the additional top (12) are used to level the surface in reference to
the working top (8) (fig. K).
Unscrew the head locking screw before starting to work
with the rail tile saw. Otherwise moving the head with cutting
disc will be impossible. The water pump should be immersed in
water during cutting.
supply network before starting any adjustments. To ensure safe,
precise and efficient cut off saw operation, proceed with all
adjustment procedures as a whole.
After finishing all the setting and adjustment procedures ensure
that all adjustment keys are collected. Check that all threaded
joining elements are properly tightened. When making
adjustments ensure that all external parts work properly and are
in good condition. Any worn out or damaged part must be
replaced by qualified personnel before starting to use the rail tile
saw.
1 pce
SWITCHING ON / OFF
1 pce
1 pce
2 sets
8 pcs
on the rating plate of the rail tile saw. Switch on the saw only
2 pcs
when the material that is to be cut is away from the cutting disc.
2 pcs
1 pce
Switching on – press the button I of the switch (7) (fig. L).
2 pcs
Switching off – press the button O of the switch (7).
1 pce
1 pce
2 pcs
equipped with residual current protection device. Check
operation of the residual current device before starting to use
the tool.
• Insert the plug into the power supply socket.
• Press the Reset button (23) – the power indicator (24) will turn
red (fig. M).
• Start the rail tile saw.
• Press the Test button (25) – the power indicator (24) will turn
black and the rail tile saw will switch off.
• Press the Reset button (23) again and start operating the device.
operate as described above) you must remove power cord plug
from the mains socket and give the tool for repair to authorized
service workshop.
CUTTING
be outside of the cutting area. Cutting disc must rotate with
maximum rotational speed before the actual cut is started. Wait
until cooling water stream reaches the cutting disc.
Base of the mitre gauge (10) is also the longitudinal fence.
• Set 0° angle on the mitre gauge (10) and tighten the locking knob
of the mitre gauge (20).
10
OPERATION / SETTINGS
Make sure the rail tile saw is disconnected from power
The mains voltage must match the voltage specified
Plug of the power supply cord of the rail tile saw is
If the residual current device is faulty (it does not
Water pump, power cord and water supply hose must