Immotec Standard; Immotec Indirect; Access Control - Comelit 3471 Manual Tecnico

The call can be made in the following ways:
√ During normal operation
1. Enter the indirect code (e.g. 100).
2. Press
to make the call or
CALL USER
_ _ _ 100
CALL
or:
1. Scroll through the directory using
2. Press
to make the call or

IMMOTEC STANDARD

This call mode is only available when "access control" is
disabled
Art. 3471 can be used in conjunction with the Simplekey module
Art. SK9020 by connecting the two products via RS485 (see
diagram on page 100).
In this configuration, the use of Simplekey access keys (badges)
automatically allows entry of the corresponding code/name (new
key) or updating of the name only (if the code already exists) in the
directory of Art. 3471. Since a single user code (apartment) can
have up to 2 access keys associated with it under different names,
during a numeric code call from the digital module the first name of
the 2 in alphabetical order will be displayed.
N.B.: names cannot be entered and changed manually.
Badge acquisition only takes place when digital mode is in
standby

IMMOTEC INDIRECT

This call mode is only available when "access control" is
disabled
Art. 3471 can be used in conjunction with the Simplekey module
Art. SK9020 by connecting the two products via RS485 (see
diagram on page 100).
In this configuration the use of access keys allows automatic
updating of the Simplekey access key (badge) name only, as it
appears in the directory of Art. 3471. The Immotec indirect codes
and corresponding names can only be entered from a PC using
software Art. 1249B (R.I. 003 - SW rev. 2.3 or higher). Since a single
user code (apartment) can have up to 2 access keys associated
with it under different names, during a numeric code call from the
digital module the first name of the 2 in alphabetical order will be
displayed.
N.B.: names cannot be entered and modified manually.
Badge acquisition only takes place when digital mode is
in standby
1. Set the speaker unit selector to ON, see Fig.
2. Connect the terminal block.
3. Access programming mode, see page 17.
4. Select settings/call management
to cancel and exit.
CANC
.
to exit.
.
SYSTEM PARAMETERS
SELECT LANGUAGE
SECOND LANGUAGE
CALL MANAGEMENT
OK
SCROLL
5. confirm.
Select the system type and
CALL MANAGEMENT
*SIMPLEBUS
SIMPLEBUS TOP
OK
SCROLL
6.
confirm.
Select the call mode and
CALL MANAGEMENT
*STANDARD
INDIRECT CODE
IMMOTEC STAND.
OK
SCROLL
7. Set the speaker module selector to OFF.

2.6. Access control

Art. 3471 can operate in two modes:
• "access control" disabled: in this mode, every name can be
assigned a call code, which is saved in the directory. The entry
passwords must be entered separately and are not assigned to
any name.
• "access control" enabled: in this mode, a call code, an indirect
code (only in case of indirect call), a password and an RFID key
can be saved for every name listed in the directory. The option of
assigning a password or key to a name allows access identification.
When access control is enabled, the following cannot be used:
• Immotec call mode
• data loading from 1249B (R.I. 003 - SW rev. 2.3 or higher)
To switch from "access control" disabled to "access control"
enabled, all saved passwords must be deleted
To switch from "access control" enabled to "access control"
disabled, all saved passwords and keys must be deleted
1. Access programming mode, see page 17.
2. Select settings/access control.
SELECT LANGUAGE
SECOND LANGUAGE
CALL MANAGEMENT
ACCESS CONTROL
OK
SCROLL
OK
ESC
OK
ESC
OK
ESC
OK
ESC
25