Publicidad
Idiomas disponibles
Idiomas disponibles
1 Dust bag installation
a) Open the triangular shaped dust bag cover by
gently pressing down on one end of the locking
bar to release the locking mechanism.
b) Lift the upper corner of the cover away from the
vacuum housing.
c) Slide the bottom edge of the cover away so the
hinges on the cover slip out of the housing.
d) Inside the dust bag cavity a foam filter helps
to protect the motor. Be sure this filter is in place
prior to installation of the dust bag.
e) Always use a Hepa-filter when picking up
hazardous material. Remove the standard motor
filter, then fit the Hepa-filter and turn clockwise
to lock it in place. Then install the dustbag. Turn
the hepa-filter the opposite direction to remove it.
f)
Unfold the new dust bag. The upper corner of the
dust bag should be folded in so they do not
interfere with the cardboard plate resting securely
on the housing.
g) Ease the dust bag into the cavity, placing the
cardboard plate onto the exterior lip of the cavity,
make sure that the cardboard plate is fitted behind
the two small clips on the exterior lip.
h) Insert the lower cover hinges into the indentations.
Be sure the dust bag cardboard plate is resting
evenly on the lips of the cavity. Close the cover,
and make certain it clicks into place.
2 Belt
The belt locking clip is designed to hold the vacuum cleaner
securely around your waist while working.
2a) Wrap the belt around your waist. Adjust it to the desired
size, by fitting the two nylon parts together.
2b) Then you´ll insert the toothed connector into the belt
buckle until it snaps into place. To disconnect the belt when
work is finished, gently squeeze the outer clips together, and
pull connector out of belt buckle.
2c) To adjust the belt for individual comfort:
Larger: Hold the belt locking clip in one hand and slide the
nylon belt until a loop is formed. Pull the belt locking clip to
adjust the slack in the nylon belt.
Smaller: Pull the loose end of the nylonbelt until adjusted to
desired size.
3 Hose attachment
Fit the hook on the hose adapter in the recess in the hose
opening on the machine. Press and turn about one half-turn
to ensure a secure fit.
4 Wand assembly
a) To connect the wand sections together, simply
insert one section into the other, giving the two
assembled sections a firm push.
b) Adjust the length of the telescopic wand by
pressing its button and altering the wand length.
When vacuuming stairs it is recommended that
the wand is adjusted to its shortest length.
5
Tools
The accessories shown in the pictures may vary from model to model.
a)
Floor nozzle, one way for brush (hard floor) or smooth
for carpet.
b)
Universal nozzle for both hard floors and carpets
c)
Combi Brush / Nozzle useful tool for the cleaning
of upholstery, stair carpets, curtains etc.
d)
Crevice Tool designed for cleaning in narrow
spaces like furniture, radiators, corners and
joints.
6
Accessory loops
The belt is equipped with loops to conveniently hold the
vacuum's accessories. In addition, the power cord can be
held in place on the belt by snapping the nylon loop around
it.
7
Start Stop
8
Suction control lever
9
Exhaust filter
a)
Release the locking mechanism by gently pressing
down on one end of the locking bar.
b)
Ease the upper corner away from the vacuum
housing.
c)
Slide the bottom edge of the cover away so the
hinges on the bottom edge of the cover slip out of
the housing.
d)
Remove filter holder and used filter.
e)
Install new filter and secure with the filter holder.
f)
Reinstall exhaust cover as in "Dust Bag
installation"
10 WARNING!
Never attempt to vacuum liquid, glass fragments or ashes!
Wet surfaces can expose the operator to possible electrical
shock.
IMPORTANT!
The UZ 964 is equipped with a specially designed cable,
which if damaged, must be replaced by a cable of the same
type. These cables are avaible at authorized service shops
and must be installed by trained personnel.
The UZ 964 is equipped with a thermal cut-out to protect the
motor and other vital machine parts from overheating. Should
the machine cut out, you will have to wait at least 5-10
minutes for it to automatically reset. While you are waiting,
switch the machine off and unplug it, then check the hose,
dust bag and filters to be sure that nothing is blocking the flow
of air through the machine.
7
Publicidad
