Technical Data - Bosch GCM 10 MX Professional Manual Original

OBJ_BUCH-2583-003.book Page 23 Thursday, September 1, 2016 7:50 AM

Technical Data

Mitre Saw
Article number
Rated power input
No-load speed min
Weight according to
EPTA-Procedure 01:2014
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 26.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 61029-1,
EN 61029-2-9, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ECS
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Mitre saw with mounted saw blade
– Tilt-protector bar 24 with fastening set 35 (2 bolts, 2
washers, 2 square nuts)
– Dust bag 19
– Material clamp 18
– Hex key/cross-head screwdriver 22
Bosch Power Tools
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
GCM 10 MX
devices are fully functional. Any lightly damaged parts must
3 601 M29 02. be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
3 601 M29 0P.
that ensure faultless operation.
W 1700
Damaged protective devices and parts must be immediately
-1
4800
replaced by an authorised service centre.
Mounting Individual Components
kg 16.8
– Carefully remove all parts provided from their packaging.
/II
Remove all packing material from the power tool and the
accessories provided.
Mounting the Tilt-Protector Bar (see figure A)
Before using the power tool for the first time, the tilt-protec-
tor bar 24 must be mounted.
mm 254
Use the "tilt-protector bar" fastening set 35 for mounting.
mm 1.8–2.8
– Insert the square nuts 35 into the intended holes 34 in the
mm 30
base plate.
– Place the washers 35 on the fastening bolts 35 and use
them to screw the tilt-protector bar 24 into the inserted
nuts.
 Never remove the tilt-protector bar. Without the use of
the tilt-protector bar, the machine does not stand safely
and can tip over, especially when sawing at maximum mi-
tre/bevel angles.
Mounting the Extension Bars (see figure B)
Long workpieces must be underlaid or supported at their free
end.
To extend the saw table additionally, extension bars can be
mounted both to the left or right of the power tool.
– Insert the extension bars 36 on both sides of the power
tool to the stop in the drill holes 16 intended for this pur-
pose.
– Tighten the fastening bolts 37 to secure the extension bars.
Stationary or Flexible Mounting
 To ensure safe handling, the machine must be mounted
on a level and stable surface (e. g., workbench) prior to
using.
Mounting to a Working Surface (see figures C1–C2)
– Fasten the power tool with suitable screw fasteners to the
working surface. The mounting holes 14 serve for this pur-
pose.
or
– Clamp the power tool with commercially available screw
clamps by the feet to the working surface.
Mounting to a Bosch Saw Stand
With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
piece supports of the saw stand are used for underlaying long
workpieces.
 Read all safety warnings and instructions included with
the worktable. Failure to observe safety warnings and in-
structions can lead to electrical shock, fire and/or cause
serious injuries.
English | 23
1 609 92A 3A2 | (1.9.16)