Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Use
Ducting version
The hood is equipped with a top air outlet B for discharge of
fumes to the outside (exhaust pipe and pipe fixing clamps not
provided).
Installation
The minimum distance between the supporting surface for the
cooking equipment on the hob and the lowest part of the
range hood must be not less than 50cm from electric cookers
and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
Electrical connection
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If provided with
a plug connect the hood to a socket in compliance with current
regulations and positioned in an accessible area, after
installation. If it not fitted with a plug (direct mains connection)
or if the plug is not located in an accessible area, after
installation, apply a double pole switch in accordance with
standards which assures the complete disconnection of the
mains under conditions relating to over-current category III, in
accordance with installation instructions.
Warning! Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that
the mains cable is correctly assembled.
Mounting
Fig.1
•
Pull handle F and remove the fat filters (1)
Note: the number of fat filters can vary on the basis of
the dimensions of the hood.
•
Remove the screws that fix the upper covers (the 900mm
model has 1 cover, models with larger widths are
supplied with 2 covers, right and left) (2).
Note: the screws to remove are in the positions indicated
by the arrow in 1.1 and 1.2 (only 900mm width model).
•
Remove the mantle(s) (3)
•
Fix connection ring B with 4 screws (4).
Note: Apply, if envisaged and/or necessary for your
installation, the reduction to the B connection ring.
Without the reduction, Ø 200mm tubes are to be used;
with the reduction Ø 150mm tubes can be used.
Fig. 2
•
Place the hole diagram on the wall (5)
•
Fix the 2 brackets to the wall using 2 screws and 2
dowels (6)
•
Hang the hood on the brackets (7)
•
Adjust the distance (8) and horizontal setup (9) of the
hood, acting on the apposite screws.
•
Mark the holes for the definitive fixing (10) from inside
and, where envisaged, from outside the hood.
Note: See the diagram of the back of the hood with the
position of the definite fixing holes/dowels/screws. (Fig.
2,1)
•
Remove the hood. (11)
•
Make the holes and insert the dowels at the points
previously marked. (12)
•
Assemble the bracket for the flue and fix it with the 4
screws supplied. (13)
Note: The extension of the bracket must be identical to
the internal width of the flue.
Fix the bracket to the wall with 2 dowels and 2 screws
(14)
•
Hang the hood on the brackets again. (15)
•
Fix the hood definitively. (16)
Note: consult montage operations 10-12 for the number
and position of the definitive fixing screws.
Fig. 3
•
Apply a discharge tube (to purchase) to the connection
ring. (17)
•
Connect the electricity. (18)
•
Fix the upper flue with 2 screws (19A) to the bracket
(19B)
•
Lower the lower section of the flue (20) and fix it onto the
upper side of the hood with 2 screws (21 - Fig. 3.1).
Fig. 4
•
Reposition the cover/s over the hood and fix it/them from
inside the hood (22).
Note: the screws must be inserted into the positions
indicated by the arrow in figure 4.1 and (4.2 - only
900mm width model).
•
Mount the fat filters again.
11
Publicidad
Tabla de contenido
