Gb Installation Instructions - Bpt XKP/300 Instrucciones Para La Instalación

4
2
3
2
3
1
Alla fine del ciclo di vita dell'appa-
recchio evitare che lo stesso
venga disperso nell'ambiente.
Lo smaltimento dell'apparecchia-
1
tura deve essere effettuato rispet-
tando le norme vigenti e privile-
giando il riciclaggio delle sue parti
costituenti.
Sui componenti, per cui è previsto
lo smaltimento con riciclaggio,
sono riportati il simbolo e la sigla
del materiale.
GB INSTALLATION
INSTRUCTIONS
WARNING. It is recommended to
install the video handset in a dry
place.
WALL MOUNTINGS
6
XKP/300+XKP/85
Set the embedding box (three-
module version, or round with 65
mm) so that it is flush with the wall
at an appropriate height for the
user.
Join the mountings using the two
joints, figure 2, and insert the two
rectangular hole plugs on the outer
sides, figure 1.
Remove the connecting cable con-
nector from the XKP/300 mounting
slot and pass it through the rele-
vant hole towards the XKP/85
mounting, figure 2.
Fix the mounting to the wall by
means of provided retainers and
screws, figure 3, 4 and 5.
Having made the connections,
position the wires so that they do
not pass over the XKP/300 moun-
ting's lower fastening screws.
XV/200 (XVC/200) MONITOR
MODULE WITH XC/300
HANDSET MODULE
Make sure the locking latch is in
the left position
7
Insert the monitor module on the
XKP/300 wall mounting and insert it
on the actual support by pushing
downwards, figure 6.
In order to prevent the module from
falling subsequent to accidental
knocks, secure it to the mounting
by moving the locking latch to the
right, figure 6.
Pass the monitor module connec-
ting cable through the opening in
the base of the handset module,
figure 7.
Insert the base on the XKP/85
mounting and insert it on the actual
support by pushing downwards,
figure 8.
Secure the base in place using the
screw supplied and make the con-
nection between the modules, figu-
re 8.
Fit the handset module housing
and apply the two side panels,
figure 9 and 10.
Insert the cable connector of the
receiver in the base and hang up
the receiver, figure 11 and 12.
8
• Dimensions: 239x224x74 mm.
WARNING. The use of the monitor
module alone, in system 300 instal-
lations, is possible in combination
with the CTI/304 interface, or
telephone interface IT/300.
WALL MOUNTING XKP/300
Set the embedding box (three-
module version, or round with
65mm) so that it is flush with the
wall at an appropriate height for
the user.
Insert the two rectangular hole
plugs on the outer sides of the
mounting, figure 13.
Fix the mounting to the wall by
means of provided retainers and
screws, figure 14, 15 and 16.
XV/200 (XVC/200)
MONITOR MODULE
Make sure the locking latch is in
the left position
Insert the monitor module on the
XKP/300 wall mounting and insert it
on the actual support by pushing
downwards, figure 17.
In order to prevent the module from
falling subsequent to accidental
knocks, secure it to the mounting
by moving the locking latch to the
right, figure 17.
Apply the two side panels, figure
18 and 19.
• Dimensions: 154x224x52 mm.
FUNCTION OF EACH TERMINAL
Support XKP/300
Terminal block M1
B line
Terminal block M2
12V AC 14÷18V DC
monitor module supply voltage
XC/300 handset modul
B line
landing call
− ground
Jumper SW1
, figure 6.
Normally supplied ready inserted.
Remove the jumper in the event the
volume of the call note is to be atte-
nuated.
Function of jumpers SW1 and
SW2 of board XKP/300
SW1: normally supplied ready
inserted (ON).
The function and position are indi-
cated in the units for which their
use is required.
SW2: normally supplied inserted in
the XC position (monitor module
switched on by means of XC/300
module).
It must be inserted in the XT posi-
tion when the monitor module is
combined with telephone module
XT/200.
Function of jumper SW3 of board
XKP/300-1
Normally supplied ready inserted
(ON) to apply the end-of-line clo-
sing resistance.
Remove the jumper if the line con-
tinues.
, figure 17.
3