Maxi-Cosi Pebble Pro. i-Size Manual De Instrucciones página 39

A - Cover (fabric)
B - Baby-hugg inlay
C - Comfort headrest
D - Push button for releasing Pebble Pro i-Size
from pushchair
E - Ergonomic handle
F - Belt hook for shoulder part of belt
G - Height adjustment shoulder belts
H - Instruction manual
I - Storage compartment
J - Small hook for clamping sun canopy
K - Sun canopy (built-in)
L - Carrying handle
M - Storage flap sun canopy
N - Push button for adjusting carrying handle
O - Shoulder belts with removable belt pads
P - Belt hook for lap part of belt
Q - Belt buckle
R - Crotch strap with belt pad
S - Mounting bars for base
T - Belt tensioner strap
SAFETY
General instructions
• Do not use the Pebble Pro i-Size for more than 6 years.
Pebble Pro i-Size and your baby
1.Make sure you can fit no more than one finger between
the harness and your baby (1cm). If there is more space
than 1 cm, tighten the harness belt further.
2. Only use the baby-hugg inlay of the Pebble Pro i-Size
when the shoulder belts are in the lowest position.
3. The headrest can be used in the car seat as long as
desired and removed, if preferred.
WARNING:
• Never place the car seat on an elevated surface (such
as a table or chair).
• Install the car seat only rearward-facing in the car.
Pebble Pro i-Size car use
1. Only use a forward-facing seat that is fitted with
a 3-point safety belt that complies with the ECE R16
standard.
2. Make sure the car safety belt buckle runs in a straight
line and stays below the belt hook of the car seat.
3. The car safety belt must be threaded tight along
all blue markings. For a proper installation, check the
instruction in this manual and the sticker on the side of
the car seat.
Pebble Pro i-Size in airplanes
• Installation of the Pebble Pro i-Size on an aircraft seat
differs from the installation on a car seat.
• Installing the Pebble Pro i-Size with a 2-point safety
belt is only allowed when used in an aircraft.
• In an aircraft, the Pebble Pro i-Size may only be used on
forward-facing passenger seats.
• To install Pebble Pro i-Size, place the infant carrier
rearward facing on the passenger seat.
Route the webbing of the-2point safety belt through
the belt guides. (1,2)
Lock the buckle of the 2-point safety belt. (3)
And tighten the 2-point safety belt by pulling on the
tightening strap. (4)
• The handle of the Pebble Pro i-Size must be in upright
position.
• The belt buckle must not be positioned between the
belt hooks of this car seat. Otherwise a safe attachment
does not exist.
• To uninstall Pebble Pro i-Size, open the buckle of the
2-point safety belt by lifting the lever of the buckle. (5)
And remove the webbing of the 2-point safety belt from
the guides. Make sure the Pebble Pro i-Size does not fall
from passenger seat when opening the buckle.
• The Pebble Pro i-Size must remain belted on the
aircraft seat, even when unoccupied.
• The Pebble Pro i-Size is only for use on an aircraft seat
authorized by the airline.
• Do not install the Pebble Pro i-Size in the area of airbag
deployment.
• Instructions of the cabin crew must be followed.
• The safety of your child for not complying with the
installation and instruction manual is not guaranteed.
Care
The cover, cushions and belt pads of the car seat can be
removed in order for these to be cleaned. They can be
machine-washed.
EN
I I
Maxi-Cosi Pebble Pro. i-Size 39