General Description; Cable Calibration; Charge Modes - GYS FLASH 15.24 XTREM Traducción De Las Instrucciones Originales

Translation of the original instructions

GENERAL DESCRIPTION

The GYSFLASH 15.24 Xtrem is a highly stabilized power supply based on inverter technology. Designed to recharge and maintain
batteries lead batteries (liquid/AGM/gel... etc.) at 12 V or 24 V. It is also a 12 V (14.3 V) or 24 V (28.6 V) stabilized power supply. The
mechanic of this product is designed to operate in very demanding environments: military settings, heavily polluted areas, quarries.
It is considered as a fixed device not a mobile product.
This charger is perfectly suitable for charging and maintenance of:
- 12 V lead batteries (6 cells in series) from 10 Ah to 240 Ah
- 24 V lead batteries (12 cells in series) from 10 Ah to 240 Ah

CABLE CALIBRATION

Procedure for calibrating the charging cables of the device, so that the charger optimally compensates for the voltage drop due to
the cables. It is strongly recommended to perform this procedure each time the cables are modified or changed.
1. Before starting, make sure that the charger is disconnected from the mains socket.
2. Short-circuit the ends of the charging cables.
3. Simultaneously press the mode
4. Plug into the power outlet while holding down the two buttons until the indicator
5. Results :
- Light on : Calibration has been carried out correctly.
- Indicator on : calibration failed, unplug the mains plug and repeat the procedure.
6. Unplug the mains plug until the charger switches off.
START UP
1. Connect the charger to the battery.
2. Plug the charger to the mains (single phase 220-240Vac 50-60Hz).
3. Select the mode by pressing the mode button
the charge starts automatically.
4. During the charge, the device indicates the charge progress. When the light
engine. Once the indicator
5. Charging can be interrupted at any time by unplugging the power plug or pressing the mode button
6. After the charge, disconnect the charger from the mains, then disconnect the clamps from the battery.

CHARGE MODES

• Description of charging modes and currents :
12 V
Lead Charging Mode (14.4 V/15 A max.):
Mode for charging 12V lead acid batteries from 10Ah to 240Ah. Automatic seven step charge cycle.
24 V
Lead Charging Mode (28.8 V/15 A max.):
Mode for charging 24V lead acid batteries from 10Ah to 240Ah. Automatic seven step charge cycle.
*This charger automatically starts recharging batteries from 1 V. When recharging a deeply discharged
lead acid battery (voltage less than 1V), it is possible to force the charge to try to recover it. Set the char-
ger to the desired operating mode (12 V or 24 V) and then press and hold button
charger starts the selected charging cycle while trying to recover the battery.
*12 V Supply: allowing the charger to be used as a stabilized power supply with a voltage regulated at 14.3 V and delivering up to
15 A. This mode can be used without a battery. To select this option, place the charger in 12 V mode and press the mode button
until the supply indicator
*24 V Supply: allowing the charger to be used as a stabilized power supply with a voltage regulated at 28.6 V and delivering up to
15 A. This mode can be used without a battery. To select this option, place the charger in 24 V mode and press the mode button
until the supply indicator
Charging current 5 A, 10 A and 15 A:
Selection to optimize the charging current according to the type of battery (lead or lithium) and its capa-
5 A 10 A 15 A
city.
Charging current
Battery capacity
GYSFLASH 15.24 XTREM
and current selection
and the charging current by pressing button
stays on, the battery is completely charged.
lights up.
lights up.
Pb 10
buttons.
or
flashes, the battery is ready to start the
5 A 10 A
45 Ah 45 90 Ah
lights up.
. After roughly five seconds,
.
for 5 seconds. The
15 A
90 240 Ah
EN
9