LEGRAND Pass & Seymour Manual De Instrucciones

LE09645AA说明书 材质：80克纸 2C 规格：148*210MM 2017.10.25
No: 341211 – 04/18
Catalog Number(s) • Numéro(s) de Catalogue • Les Numéros de Catalogue: LIWC
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
Wireless Nominal
Output: 5V, 1A
Rating: 120VAC
Sortie nominale
sans fil : 5 V, 1 A
Cote : 120 V c.a.
Salida Nominal
Inalámbrica: 5V, 1A
Clasificación: 120VAC
FCC COMPLIANCE — FCC ID: YV8-LIWC IC:9922A-LIWC HVIN: LIWC
CAUTION: Changes or modifications not expressly approved
could void your authority to use this equipment. This device
complies with Part 15 of the FCC Rules. Operation to the
following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
To comply with FCC and other RF exposure requirements, please
maintain a distance of 10cm between the charger and your body
when in use.
INDUSTRY CANADA – This device complies with Industry Canada
license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that
may cause undesired operation of the device.
DESCRIPTION: This device is a Qi-Certified integrated wireless charger. It
provides 1A total DC power at 5V for charging phones equipped with a Qi
receiver. The wireless charger is intended for charging purposes only and is
not intended for data transfer.
Qi STANDARD:
• Qi (pronounced "chee") is the global standard for compatible
wireless charging.
• Just like Bluetooth ® set the standard for exchanging data over short
distances or Wi-Fi™ set the standard for wireless networking, Qi sets the
standard for wireless charging.
• To charge, you just place a Qi-enabled device on a Qi charging surface,
there are no cords to plug into the phone.
• To find Qi compatible devices, go to:
https://www.wirelesspowerconsortium.com/products.
HOW Qi WORKS:
• Qi works by generating a safe
electromagnetic field between a
charger and a device through a
well-established process called
magnetic induction. Magnetic
induction has been used for more
than a century to make power
transformers.
• Qi chargers have a built-in
transmitting coil that intelligently
communicates with Qi devices
using a specific electromagnetic
frequency, so any Qi device will
work with any Qi charger, now and
in the future.
Pass & Seymour
Legrand Qi-Certified Integrated Wireless Charger
Chargeur sans fil intégré certifié Qi Legrand, 5 V c.c., 1 A
Cargador inalámbrico integrado Legrand Qi-certified, 5VDC, 1A
Installation Instructions • Notice d'Installation • Instrucciones de Instalación
LE09645AA说明书 材质：80克纸 2C 规格：148*210MM 2017.10.25 LE09645AA说明书 材质：80克纸 2C 规格：148*210MM 2017.10.25 LE09645AA说明书 材质：80克纸 2C 规格：148*210MM 2017.10.25
Fig. 1
MISE EN GARDE : Les changements ou les modifications
qui ne sont pas expressément approuvés pourraient annuler
votre autorisation d'utiliser ce matériel. Le présent appareil est
conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. Le exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Afin de se conformer ´ a la FCC et aux autres exigences visant
l'exposition aux radiofréquences, conserver une distance de 10 cm
entre le chargeur et votre corps pendant l'utilisation.
Figure 2
INSTALLATION
INSTRUCTIONS:
1) Select the "US" plug adapter shown In Fig. 1 and attach
to the power supply – align tabs with slots, push down
and rotate clockwise until it clicks (locks). NOTE: Use
only the power supply and the cord supplied in the box.
2) Cut mounting hole using 3-1/8" (80mm) hole saw. See Fig. 2.
2) Adhere the "Wireless Charging Station" decorator ring shown in Fig. 1 to
the top side of the mounting hole (if desired)
3) Insert the hex head of the plastic mounting bolt into the bottom side slot
of the wireless charger. See Fig. 3.
4) Install as shown in Figures 3-5.
5) Connect power.
6) Place device on charging pad and refer to chart below for LED operation.
LED
Color
Orange
White
®
LE09645AA说明书 材质：80克纸 2C 规格：148*21
PRECAUCIÓN: Los cambios o modificaciones que no sean
expresamente aprobados podrían anular su autoridad para usar
este equipo. Este dispositivo cumple con la Part 15 de las Reglas
de la FCC. Operación bajo las siguientes doe condiciones: (1)
Este dispositivo no debe provocar interferencia dañina, y (2) este
dispositivo debe aceptar cualquier interferencia recibida, incluso
interferencia que pueda provocar una operación no deseada.
A fin de cumplir con la FCC y otros requisitos de exposición a
frecuencia de radio, mantenga una distancia de 10 cm enter el
cargador y su cuerpo cuando esté en uso.
3-1/8''
Ø 80 mm
Figure 5 120V~ – 5 VDC – 1000 mA
Operational Status
Standby Charging Complete
Off On Off
On (Dimmed) Off On
Figure 3 Figure 4
Fault Power On
Blink Slow Off - On - Off
Off On - Off - On