Fein FSC1.6X Manual De Instrucciones página 21

en
20
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of sanding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty the
dust collector/container in time, observe the material
manufacturer's working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Emission values for vibration
Vibration
Classification of FEIN application
tools according to vibration class
VC0
VC1
VC2
VC3
VC4
VC5
K
* These values are based on a work cycle consisting of no-load
and full-load operation of the same duration.
For information on the vibration class assigned to the application
tool, please see the enclosed data sheet 3 41 30 213 06 2.
Operating Instructions.
Changing the tool FSC1.6Q/FSC2.0Q (see page 5).
Do not use accessories not specifically intended and
recommended for this power tool by FEIN. The use of non-
original FEIN accessories can lead to overheating of the
power tool and destroy it.
When changing application tools with sharp cutting
edges, use cover 3 21 74 011 00 0 to protect your-
self against hand injuries.
Firmly press in the fastening element to the stop.
Then lock the clamping lever.
Protect your hand and fingers against bruising when
locking the clamping lever. The clamping lever
snaps back vigorously by means of spring force.
Additional operating instructions.
Guide the power tool toward the work piece only
when switched on.
Before using, sharpen used and even new cutter blades
with the cleaning block.
The symptom for worn blades is a clearly increased feed
force at lower working progress.
The application tool can be offset in 30° steps and fas-
tened in the most favourable working position.
Guide straight, bent or offset cutter blades at a right angle
to the window flange (see page 11-12, Cutter blades
A – D).
For U-shaped cutter blades, pay attention that the
traverse of the cutter blade is led parallel to the window
pane of the vehicle (see page 12, Cutter blades E – F).
The scraper knife is used for cutting back bond remain-
ders on the window flange or the pane. Before re-bond-
ing the vehicle window, cut back the remaining bead to a
height of approx. 2 mm (see page 12, Cutter blades G).
Repair and customer service.
The total insulation of the power tool can be impaired.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air,
and connect a residual current device (RCD) on the line
side.
If the supply cord of this power tool is damaged, it must
Weighted
be replaced by a specially prepared cord available through
acceleration*
the FEIN customer service centre.
2
< 2,5 m/s
The current spare parts list for this power tool can be
2
< 5 m/s
found in the Internet at www.fein.com.
2
< 7 m/s
If required, you can change the following parts yourself:
2
application tool, fastening element (FSC1.6Q/FSC2.0Q)
< 10 m/s
2
< 15 m/s
Warranty and liability.
2
> 15 m/s
The warranty for the product is valid in accordance with
2
3 m/s
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. FEIN GmbH, C-DB_IA,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.