Publicidad
Idiomas disponibles
Idiomas disponibles
BR MINUTEUR TOURBILLON
Te c h n i c a l N o t e s
GENERAL DESCRIPTION
: mechanical, manual winding with tourbillon rotating once a minute.
Movement
41 rubies. 21,600 vibrations/hour.
Functions
reserve indicator (72 hours - 3 days). Timer counting the hours and minutes from a chosen
moment (two possible measuring scales for the minute hand: one with sixty graduations
to measure the minutes and one with ten sectors to measure the 10
diagram below). A button (E) resets the timer.
phire caseback and
.
crystal
Water-resistance
GENERAL USE
Activation
. Crown in position 0. With the watch stopped, wind the mechanism by turning
the crown clockwise. The power reserve (C) increases in proportion to the winding. It
indicates the number of running days remaining.
the movement before the power reserve hand reaches the "top" (or maximum) gradua-
tion. This will prevent any risk of damaging the mechanism whilst optimising the accuracy
of the watch.
. Pull the crown to position 1. Set the time by turning the
Setting the time
crown in the desired direction.
USING THE TIMER (hours, minutes and 10
The timer (or chronograph with two central hands) is used to measure a short time
from a chosen moment.
Pressing initially (P1) on push-piece E at moment T triggers the timing operation. The
minute hand (F) indicates the minutes timed from moment T on the large, 60-division
graduation. The hour hand (D) indicates the hours timed on the same graduation. A spe-
cial graduation broken down into ten sectors (at the centre of the timer) indicates, with
the minute hand (F), the 10
of an hour. This original graduation is used in certain profes-
ths
sions which count the hours on a decimal scale (see diagram below). Pressing again (P2)
activates the timer reset.
Comment
: the timer appears to be stopped after resetting.
Hand F can only be seen moving after timing for two minutes. This difference corresponds
to the mechanism's precision tolerance.
B
C
D
60
E
P1-P2
30
F
G
(x4)
H
A. Minute hand
B. Hour hand
C. Power reserve indicator
D. Timer hour hand
E. Timer push-piece
F.
Timer minute hand
G. Bezel fixing screws
(NEVER LOOSEN)
H. Small second
I.
Tourbillon carriage
J.
Crown
K. Strap fastener or part fixing the strap to the case
L. Screws fixing the strap to its fastener (K)
M. Access screw to crown dismantling push-piece
0.
Wind the mechanism manually (clockwise)
1.
Set the time (clockwise or anti-clockwise)
P1. Pressing push-piece E initially triggers the timing operation
P2. Pressing again activates the timer reset.
Comment: the timer appears to be stopped after resetting.
Hand F can only be seen moving after timing for two minutes
2.
Loosen the four screws (L) to dismantle the strap
(anti-clockwise)
: hour, minute and second indication. Power
ths
of an hour (see
Case
: 44 mm x 50 mm. Anti-reflective sap-
: 50 m.
: we advise you to stop winding
Caution
of an hour)
ths
A
K
(x2)
0
1
J
(x2)
I
(NEVER LOOSEN)
DISMANTLING THE STRAP AND ITS TWO FASTENERS
Your watch comprises three assemblies:
Assembly 1: the main body of the case
Assembly 2: the bezel, a sort of "cover" for the case
Assembly 3: the two strap fasteners (K)
Two types of screw are used to assemble the three:
The four split-head screws (G) fix the cover to the case body and ensure that the watch
is water-resistant.
Caution
Bell & Ross warranty.
The four hollow-head screws (L) (hexagon slot/1.3 mm in diameter) attach the strap to
the fasteners (K). These screws may be handled with care by using the two appropriate
tools supplied with the watch in its presentation case.
IMPORTANT
Water-resistance
. Once the time has been set, push the crown back to position 0.
The crown should never be manipulated under water.
MAINTENANCE
It is advisable to rinse the watch and its strap carefully in fresh water after every immer-
sion in sea water. It is also advisable to have the water-resistance of your watch checked
every two years. To guarantee service in compliance with brand requirements, any work
on your watch must be carried out by the Bell & Ross repair centre or a Bell & Ross-
approved watchmaker. You should present the Bell & Ross warranty card, duly dated and
signed by the retailer when the watch was purchased, for any work within the warranty
period.
2
L
(x4)
READING THE TIMER (ExAMPLE)
D
60
F
30
The Bell & Ross international guarantee
Your Bell & Ross watch has successfully passed the most rigorous reliability tests in the Swiss watch-making
industry. It is guaranteed against all manufacturing defects for 2 years from the date of purchase entered by the
Bell & Ross approved retailer on the international guarantee certificate subject to applicable laws and/or legal
guarantees. This guarantee is total (parts and labor). It excludes however:
. Damage that is the result of accidents or improper or incorrect use of the watch (violent shock, crushing,
brutal handling of the clasp).
. Damage that is the result of repairs or dismantling not carried out by an approved Bell & Ross retailer or an
approved after-sales service center.
. The results of normal use and wear of the watch and strap. This also excludes batteries given the specific
nature of these items.
IMPORTANT : To be covered by the Bell & Ross International Guarantee, any work must be carried out by
approved specialists : retailers approved by Bell & Ross, approved after-sales service centers.
This guarantee can only be applied on presentation of the Bell & Ross International Guarantee certificate, duly
completed, dated and signed by an approved retailer.
Models and Technical features subject to change
: loosening these screws will automatically invalidate the
BR XT - TOURBILLON - R - GOLD - LIMITED EDITION 01/30
M
(x1)
WATER-RESISTANT 50 M - SWISS MADE 750
The hour hand (D) indicates 11 o'clock
on the large, 60-division graduation.
The minute hand (F) indicates 9 minutes
on the large graduation or 0.2 hours on the
decimal scale in the central graduation.
Publicidad
