Weber PULSE 2000 Manual Del Propietário página 9

Ocultar thumbs Ver también para PULSE 2000:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

WEBER CONNECT App
First things first.
Download the WEBER CONNECT app.
To fully activate and update your new
PULSE grill, it is important to first
download the WEBER CONNECT app.
Download, connect and register to receive:
• Flip and Serve Notifications
• Food Readiness Countdowns
• Custom Food Doneness Alerts
• Step-by-step Grilling Assistance
Connecting Your Grill To Bluetooth® or
Wi-Fi Network
To connect your WEBER PULSE grill via Bluetooth® or to
your local Wi-Fi network, follow these steps:
NOTE: WEBER recommends that your smart device be
running the latest version of its operating system before
attempting to connect your grill to Bluetooth® or your
Wi-Fi network.
1) Push the red power button located on right side of
temperature controller to turn ON the grill.
2) Verify that your smart device is connected to
Bluetooth® or your local Wi-Fi network.
3) From your smart device, download the new WEBER
CONNECT app from the App Store on Apple devices,
or the Play Store on Android devices.
4) Open the WEBER CONNECT app and follow the
in-app instructions for connecting to your PULSE
grill.
NOTE: In order to successfully connect your smart device
to your grill via a local Wi-Fi network, first make sure your
grill is paired via Bluetooth® and that your grill is within
range of your Wi-Fi router. If your attempts to connect have
been unsuccessful, try moving the grill within range of
the Wi-Fi router or adding a signal extender for a stronger
signal.
WARNING
m
Risk of injury! The probes are very
m
sharp. Please be careful when
handling probes.
Risk of burns! Handling the food
m
probes without hand protection will
result in severe burns. The colored
probe indicators are not intended
to be touched with bare hands
while using the grill as they are not
heat-insulated. Please wear heat-
resistant gloves at all times while
using this product in order to avoid
being burned.
Grilling with Food Probes
Use the included food probes to monitor of your
WEBER PULSE for the perfect food, every time.
Please follow these steps for using food probes:
1) Once the grill has been preheated, open the grill lid
and clean the cooking grates using a grill brush or
scraper, then set the control knobs to the desired
grill temperature.
2) Place your food on the grates.
3) Plug in the food probe(s) to the port of the
temperature controller (F) and, using heat resistant
grill mitts or gloves, route food probe cables through
the side channel on the grill (G).
4) Insert food probe(s) into the center of the thickest
part of your food.
5) Close the grill lid.
6) From the WEBER CONNECT app, select a desired
food to cook or select a Cook Program. You will
receive a notification when your food has reached
the set temperature(s) and your cook has ended.
Probe Usage
The colored probe indicators are for visual
identification of the probe(s) within the app.
• To ensure an accurate reading, please insert the probe
a minimum depth of 0.4 inches (10 mm) into the center
of the meat (H). For poultry, it's best to place the probe
in the thickest part of the thigh or breast, avoiding the
bone. For thick cuts of flat meat, insert the probe into
the middle of the meat from the top or the sides .
To ensure safe usage of the meat probe and to prevent
damage to the probe:
• Do not expose the probe or its wiring to direct contact
with the cooking grate.
• Route food probe cables through the side channel on
the grill to ensure that the grill lid closes.
• Do not submerge the probe or its wiring in liquid.
• Probe is not dishwasher safe.
Important Note: When using probe, be sure to route wire
where it will not be exposed to flames or temperatures
exceeding 715° F (380° C). Avoid exposing probe to
temperatures below -22° F (-30° C). Temperatures below
-22° F (-30° C) or above 572° F (300° C) will not display
in the app and will cause the probe to disappear from
connection.
Cool Down
When finished grilling, turn control knob(s) off, unplug
the power cable and allow the temperature controller
to cool. Remove the temperature controller and store
indoors in the storage box when not in use.
F
G
H
9

Publicidad

Tabla de contenido
loading

Tabla de contenido